SafeSequence › UK Safety Template Library › High-Volume UK COSHH › Bleach COSHH Risk Assessment Template (Sodium Hypochlorite UK Word .DOC & SDS Guide)
Reference UK COSHH Example • High-Volume UK COSHH

Bleach COSHH Risk Assessment Template (Sodium Hypochlorite UK Word .DOC & SDS Guide)

Under COSHH Regulations 2002 Regulation 6, employers must conduct a suitable and sufficient task-specific risk assessment for sodium hypochlorite (bleach) exposure before work commences. HSE EH40/2005 sets a Workplace Exposure Limit (WEL) of 0.5 ppm (15-minute STEL) for chlorine gas evolved from bleach. UK CLP classifies bleach as GHS05 Corrosive (H314: causes severe skin burns and eye damage). A manufacturer's Safety Data Sheet (SDS) alone does NOT satisfy Regulation 6; employers must assess task-specific exposure routes, implement engineering controls (local exhaust ventilation, closed-transfer systems), provide appropriate BS EN-certified PPE, establish emergency procedures, and document residual risk using a 5×5 matrix. This audit-grade template guides UK duty-holders through hazard identification, exposure assessment, hierarchy of control selection, and competent person sign-off to achieve residual risk ≤6 (Low) and demonstrate legal compliance during HSE inspection or CDM tender pre-qualification.

Statutory FrameworkCOSHH Regulations 2002 Reg 6, HSE EH40/2005 Chlorine WEL (0.5 ppm STEL), UK CLP GHS05 Corrosive H314
ClassificationUN 1791 Hypochlorite Solution (≥5% available chlorine). UK CLP/GHS Classification: GHS05 Corrosive (Skin Corr. 1B H314: Causes severe skin burns and eye damage; Eye Dam. 1 H318: Causes serious eye damage). Aquatic Chronic 2 H411. HSE EH40/2005 WEL for evolved chlorine gas: 0.5 ppm (1.5 mg/m³) 15-minute STEL. No 8-hour TWA assigned. Bleach reacts violently with acids (releasing chlorine gas), ammonia, and organic solvents. Store in original HDPE containers below 25°C, away from incompatible substances. Supplier SDS must be current (UK REACH/CLP compliant) but does NOT replace employer's Regulation 6 task risk assessment.
Required Plant / KitCalibrated chlorine gas monitor (0–1 ppm range, HSE-approved) • Closed-loop dosing pump with anti-siphon valve (for bulk transfer) • HDPE measuring jugs with pour spouts (graduated, chemical-resistant) • Local exhaust ventilation (LEV) system with TH2 thorough examination certificate (14-month intervals) • Emergency eyewash station (BS EN 15154-2:2006, plumbed or self-contained, weekly flush log)
Site Sign-Off StatusRequires Competent Person Verification
Bid-Winning PCI Tender Studio or Instant Voice Customization

Bidding a Contract or Need This COSHH Customized for Your Site?

Drop your client's Pre-Construction Information (PCI) PDF into our Tender Studio to generate a page-cited 5×5 RAMS & PQQ pack—or download our free blank Word (.doc) shell below.

Auto-Fill via 45s Voice / CLP

1. Mandatory Personal Protective Equipment (BS EN Standards)

BS EN ISO 374-1:2016 Type B (KPT), BS EN 374-5:2016 (permeation ≥30 min)
Chemical-resistant gloves (nitrile or neoprene, minimum 0.38 mm thickness)
Prevent dermal contact with corrosive sodium hypochlorite solution (H314). Latex and PVC offer insufficient permeation resistance.
BS EN 166:2001 (Grade 3 liquid splash, optical class 1)
Safety goggles or full-face shield (indirect vented, anti-mist)
Mandatory eye protection against splashes causing irreversible eye damage (H318). Spectacles insufficient for liquid hazards.
BS EN 14605:2005 Type 3 or Type 4 (liquid-tight)
Chemical-resistant apron or coverall (PVC or coated polypropylene)
Protect torso and legs from splashes during decanting, dilution, or spill response. Cotton/polyester workwear absorbs bleach and prolongs skin contact.
BS EN ISO 20345:2011 S5 (penetration-resistant midsole, antistatic, HRO)
Safety footwear with chemical-resistant sole and toecap
Prevent foot burns from spills on floor surfaces. S5 rating ensures water/chemical penetration resistance and slip resistance (SRC).

2. 5×5 Hazard Risk Assessment Matrix (HASAWA 1974 / CDM 2015)

Identified Hazard & HarmInitial Risk (L×S)Mandatory Engineering, Isolation & Procedural ControlsResidual Risk
1. Skin/eye contact with concentrated sodium hypochlorite solution during decanting or dilution
Harm: Severe chemical burns (H314), permanent scarring, irreversible eye damage (H318), potential blindness
4 × 5 = 20Eliminate manual handling: install closed-loop dosing system with anti-siphon valve. Substitute with lower-concentration product (≤5% available chlorine) where feasible. Engineering: use LEV (capture velocity ≥0.5 m/s at source) during bulk transfer. Administrative: written SOP, competent person training (COSHH essentials Sheet 3), two-person rule for bulk decanting. PPE: BS EN ISO 374-1 gloves, BS EN 166 goggles, BS EN 14605 apron. Emergency eyewash within 10 seconds travel time (BS EN 15154-2). Pre-task toolbox talk and permit-to-work for bulk operations.2 × 3 = 6
2. Inhalation of chlorine gas evolved from bleach (especially if mixed with acid or heated)
Harm: Acute respiratory irritation, pulmonary oedema, chemical pneumonitis, asphyxiation (HSE EH40/2005 WEL 0.5 ppm STEL)
3 × 4 = 12Eliminate mixing: segregate bleach from acids, ammonia, and incompatible chemicals (separate storage cabinets, signage). Substitution: use pre-diluted ready-to-use products. Engineering: ensure adequate general ventilation (≥5 air changes/hour) plus LEV at point of use. Install calibrated chlorine gas monitor with audible alarm set at 0.3 ppm (60% WEL). Administrative: prohibit mixing via SOP, label all containers, restrict access to trained operatives. Health surveillance: annual respiratory questionnaire for frequent users. PPE: FFP3 respirator (BS EN 149:2001+A1:2009) for emergency spill response only (not routine control).2 × 2 = 4
3. Accidental mixing with incompatible substances (acids, ammonia) releasing toxic chlorine or chloramine gas
Harm: Rapid evolution of toxic gas, acute poisoning, respiratory failure, fatalities (multiple UK HSE enforcement notices)
3 × 5 = 15Elimination: remove all acidic cleaners and ammonia-based products from bleach storage/use areas. Substitution: single-product cleaning regimes where possible. Engineering: dedicated storage cabinet with spill containment (110% capacity), segregated by 3 m minimum. Administrative: COSHH training emphasizing incompatibility, colour-coded containers (bleach = yellow label), written prohibition on mixing, supervisor spot-checks. Lockout/Tagout (LOTO): lock incompatible chemical cabinets, issue keys only to competent persons. Emergency: spill kit with neutralizing agent (sodium thiosulfate), evacuation plan, 999 call procedure.1 × 4 = 4
4. Manual handling of 5–25 litre containers causing musculoskeletal injury
Harm: Back strain, shoulder injury, dropped containers leading to splash exposure
4 × 2 = 8Elimination: bulk delivery with fixed dosing system. Substitution: order smaller 5 L containers instead of 25 L drums. Engineering: provide drum trolleys, tilt stands, or pump dispensers to eliminate lifting. Administrative: Manual Handling Operations Regulations 1992 assessment, two-person lift for >10 kg, training in kinetic handling techniques. Workplace design: store at waist height (750–1200 mm), avoid overhead storage. PPE: anti-slip gloves (BS EN 388:2016 minimum 1121X) to maintain grip.2 × 2 = 4
5. Spill or leak creating slip hazard and prolonged vapour exposure in confined space
Harm: Slips/falls, extended inhalation exposure exceeding WEL, environmental contamination (H411 aquatic toxicity)
3 × 3 = 9Engineering: secondary containment (bunded storage, drip trays with 110% capacity), impermeable flooring with drainage to sealed sump. Install spill alarm sensors in bulk storage areas. Administrative: daily visual inspection of containers/pipework, spill response SOP, designated spill kit location (absorbent pads, neutralizer, disposal bags), 24-hour emergency contact. Confined Space Regulations 1997: permit-to-work, atmospheric testing (O₂ ≥19.5%, chlorine <0.5 ppm), forced ventilation, standby person. PPE for spill response: full-face respirator (BS EN 136 Class 2 with ABEK-P3 filter), chemical suit (BS EN 14605 Type 3), long nitrile gloves. Dispose as hazardous waste (EWC 20 01 29*).1 × 3 = 3

3. Step-by-Step Safe Sequence of Operations & Hold-Points

1

Review SDS, confirm WEL, and verify engineering controls operational

Pre-Task Preparation

Obtain current UK REACH-compliant SDS from supplier (check revision date within 12 months). Confirm product concentration (typically 3–15% available chlorine). Verify HSE EH40/2005 WEL for chlorine: 0.5 ppm (15-min STEL). Inspect LEV system: check TH2 thorough examination certificate valid (14-month intervals), test airflow at capture hood (≥0.5 m/s). Confirm emergency eyewash functional (weekly flush log signed). Check chlorine gas monitor calibrated (6-month certificate) and alarm set at 0.3 ppm. Ensure spill kit stocked and accessible within 10 m.

Critical Hold-Point: STOP: Do NOT proceed if LEV is out of test, eyewash non-functional, or SDS unavailable. Regulation 6 requires controls verified BEFORE exposure. Notify supervisor and isolate area.
2

Don mandatory PPE and confirm competence of operatives

Pre-Task Preparation

All personnel handling bleach must don: BS EN ISO 374-1 nitrile gloves (inspect for tears, replace if >8 hours cumulative use), BS EN 166 safety goggles (clean lenses, check seal), BS EN 14605 chemical apron, BS EN ISO 20345 S5 safety boots. Confirm operatives hold valid COSHH Essentials training certificate (refresher every 3 years) and have read task-specific SOP (sign-off sheet). Conduct pre-task toolbox talk covering incompatibility hazards, emergency procedures, and WEL. Appoint competent supervisor (minimum IOSH Managing Safely or equivalent).

Critical Hold-Point: HOLD POINT: Supervisor must visually verify PPE compliance and competence records before authorizing task. Inadequate PPE = immediate H314 burn risk.
3

Transfer bleach using closed system or controlled pour under LEV

Decanting/Dilution

For bulk transfer: use closed-loop dosing pump with anti-siphon valve; never siphon by mouth or gravity. For manual decanting: work within LEV capture zone, pour slowly down side of receiving vessel to minimize splashing, keep face away from container opening. Use only HDPE or glass containers (never metal—corrosion risk). Label secondary containers immediately with product name, concentration, hazard pictogram (GHS05), and date. Measure quantities accurately to avoid excess (minimize waste). Maximum decant volume per session: 10 litres (reduce exposure duration).

Critical Hold-Point: NEVER mix bleach with any other chemical. NEVER add water to concentrated bleach (exothermic—add bleach to water). Mixing with acid releases chlorine gas—potentially fatal.
4

Apply diluted bleach solution following SOP exposure time limits

Application/Use

Use lowest effective concentration (typically 1:10 dilution = 0.5% available chlorine for disinfection). Apply via spray bottle, mop, or cloth—avoid aerosol generation. Maintain adequate ventilation (open windows/doors, activate mechanical ventilation). Limit continuous exposure to 15 minutes per operative (rotate tasks to stay below STEL). Keep chlorine gas monitor active and visible; evacuate if alarm sounds (>0.3 ppm). Prohibit eating, drinking, smoking in treatment area. Wash hands immediately after use, even when wearing gloves (permeation risk after 30 min).

Critical Hold-Point: STOP if irritation occurs (eyes, throat, breathing difficulty). Evacuate to fresh air, activate emergency eyewash if splashed, call 999 if symptoms persist. Do NOT re-enter until atmosphere tested <0.5 ppm.
5

Decontaminate equipment, dispose of waste, and doff PPE safely

Post-Task Decontamination

Rinse all equipment (jugs, mops, cloths) with cold water in designated sink (not food-prep area). Dispose of single-use items (wipes, PPE) as hazardous waste (EWC 15 02 02* if contaminated). Doff PPE in correct sequence: gloves (peel inside-out), apron (roll inward), goggles (handle by strap only), wash hands thoroughly with soap and water for ≥20 seconds. Return reusable PPE to designated storage (inspect for damage, replace if compromised). Wipe down work surfaces with water (neutralizes residual bleach). Record task completion and any near-miss incidents in COSHH logbook.

Critical Hold-Point: Do NOT touch face, phone, or door handles before washing hands. Residual bleach on gloves can transfer to mucous membranes causing delayed burns.
6

Complete exposure record and schedule health surveillance if threshold exceeded

Review & Monitoring

Supervisor to complete COSHH exposure log: operative name, task duration, concentration used, any deviations from SOP. If cumulative exposure >2 hours/week or concentration >10%, enrol operative in health surveillance programme (annual respiratory questionnaire, occupational health review). Review incident/near-miss reports monthly; update risk assessment if new hazards identified. Re-assess COSHH annually or after process change, product substitution, or incident. File completed assessment in site H&S file; provide copy to operatives and upload to CDM Health & Safety File if construction project.

Critical Hold-Point: Legal requirement: Regulation 6 assessment must be reviewed if no longer valid. Failure to monitor exposure or update assessment = HSE Improvement Notice risk (£20k+ fine).

Emergency Rescue, First Aid & Spill Protocol

**EMERGENCY CONTACTS:** 999 (ambulance), Poison Centre 0344 892 0111, HSE incident reporting 0345 300 9923 (RIDDOR). **SKIN CONTACT:** Remove contaminated clothing immediately. Flush affected area with copious running water for ≥15 minutes (use emergency shower if large area). Do NOT neutralize with acid/vinegar. Seek medical attention for all exposures—burns may develop over hours. **EYE CONTACT:** Hold eyelids open, irrigate with eyewash or running water for ≥15 minutes. Remove contact lenses if present and easy to do. URGENT: Transport to A&E immediately—H318 classification indicates serious eye damage risk, ophthalmology assessment required within 1 hour. **INHALATION:** Evacuate casualty to fresh air immediately. Loosen tight clothing. If breathing is difficult, administer oxygen (if trained first-aider available). If chlorine gas exposure suspected (choking, coughing, chest tightness), call 999—do NOT allow casualty to walk (risk of pulmonary oedema). Monitor for delayed respiratory symptoms up to 24 hours. **INGESTION:** Do NOT induce vomiting (corrosive—risk of oesophageal perforation). Rinse mouth with water, give small sips of water if conscious. Call 999 immediately, inform paramedics of sodium hypochlorite concentration. **SPILLAGE:** Evacuate area, ventilate, prohibit entry until atmosphere tested. Wear full PPE (respirator, suit, gloves). Absorb with inert material (vermiculite, sand), neutralize with sodium thiosulfate solution if available, collect as hazardous waste. Notify Environment Agency if >1 litre enters drain (0800 807060). **FIRE:** Bleach is non-flammable but decomposes >60°C releasing toxic chlorine/oxygen. Evacuate, use water spray to cool containers, wear BA if smoke present.

4. UK HSE & PQQ Compliance FAQs: Bleach COSHH Risk Assessment Template (Sodium Hypochlorite UK Word .DOC & SDS Guide)

Is the manufacturer's Safety Data Sheet (SDS) enough to comply with COSHH Regulations 2002 or do I need a separate risk assessment for bleach?

No—a supplier's SDS alone does NOT satisfy COSHH Regulation 6. The SDS provides hazard data (H-codes, WELs, PPE recommendations) but does NOT assess YOUR specific task, workplace conditions, exposure duration, or control measures. UK HSE law requires employers to conduct a suitable and sufficient risk assessment for each task involving hazardous substances, documenting how you will prevent or adequately control exposure in your workplace. You must evaluate your decanting methods, ventilation, PPE selection, emergency procedures, and competence—then record this in a written COSHH assessment signed by a competent person. During HSE inspection or CDM tender pre-qualification, you must produce a task-specific assessment, not just the supplier's SDS.

What is the HSE workplace exposure limit (WEL) for bleach and how do I measure chlorine gas levels during cleaning tasks?

Bleach (sodium hypochlorite) itself has no assigned WEL, but HSE EH40/2005 sets a WEL for chlorine gas evolved from bleach: 0.5 ppm (1.5 mg/m³) as a 15-minute Short-Term Exposure Limit (STEL)—there is no 8-hour TWA. Chlorine gas is released when bleach is heated, mixed with acids/ammonia, or used in poorly ventilated spaces. To measure exposure, use a calibrated direct-reading chlorine gas monitor (electrochemical or photoionization detector, 0–1 ppm range, 6-month calibration certificate). Place the monitor in the operative's breathing zone during the task; if readings approach 0.3 ppm (60% WEL), stop work, improve ventilation, and review controls. For routine low-concentration use (<5% bleach, good ventilation), atmospheric monitoring may not be necessary—but you must justify this decision in your COSHH assessment and conduct initial monitoring to confirm.

Do I need health surveillance for employees who use bleach regularly and what PPE is legally required under COSHH?

Health surveillance is required under COSHH Regulation 11 if the risk assessment identifies a realistic risk of ill health AND valid surveillance techniques exist. For bleach, consider health surveillance (annual respiratory questionnaire, occupational health review) if operatives: (a) use >10% concentration regularly, (b) work >2 hours/week with bleach, (c) have pre-existing respiratory/skin conditions, or (d) previous exposure-related symptoms. Surveillance detects early signs of sensitization or chronic irritation. Regarding PPE (Regulation 7): you must provide BS EN-certified chemical-resistant gloves (BS EN ISO 374-1 Type B, nitrile/neoprene), safety goggles (BS EN 166 Grade 3 liquid splash), and chemical apron (BS EN 14605 Type 3/4) as a MINIMUM for all bleach handling. PPE is the last line of defense—prioritize elimination (closed dosing systems), substitution (lower concentration), and engineering controls (LEV) first. Document PPE selection, training, and maintenance in your COSHH assessment; provide replacement PPE free of charge when damaged or permeation time exceeded (typically 30 minutes for nitrile gloves).

5. Operative Toolbox Talk & Competent Person Sign-Off Register

Operative / Supervisor Name Trade / Role & CSCS No. Signature Date & Time
1. (Site Supervisor):     
2.     
3.     
4.     

Automate UK Safety Documentation with SafeSequence®

Need site-specific compliance documentation instead of a static template? Explore the core SafeSequence® UK software modules hosted in AWS London (eu-west-2):

45s Voice RAMS & COSHH Dictate site tasks or select CLP diamonds to generate UK 5×5 RAMS & Reg 6 COSHH PDFs. PCI Tender-to-RAMS Studio Upload 300-page Principal Contractor PCI PDFs for [Page X] cited RAMS & PAS 91 answers. Enterprise Visual SOPs Turn shop-floor POV walkthrough video into GDPR-redacted Visual SOPs, 6S OPLs & CAPAs. HSE Consultant Vaults Multi-client white-label RAMS, Visual SOP & COSHH software for CMIOSH consultants.

Related UK Safety & Tender Templates