SafeSequence › UK Safety Template Library › Commercial Brand COSHH › Hammerite Direct to Rust Metal Paint & Brush Cleaner (Hydrocarbon / Xylene)
Reference UK COSHH Example • Commercial Brand COSHH

Hammerite Direct to Rust Metal Paint & Brush Cleaner (Hydrocarbon / Xylene) (COSHH Template & 5x5 Risk Assessment)

Under COSHH Regulations 2002, DSEAR 2002, and EH40/2005 Workplace Exposure Limits, employers must prevent or adequately control exposure to Hammerite Direct to Rust Metal Paint and Brush Cleaner containing flammable hydrocarbons and xylene (GHS02 H226 flammable liquid, GHS07 H336 narcotic effects). Mandatory local exhaust ventilation (LEV), ignition source isolation, and respiratory protection are required to achieve residual risk ≤6 (tolerable). Xylene 8-hour TWA WEL is 50 ppm (220 mg/m³) and 15-minute STEL is 100 ppm (441 mg/m³) per EH40/2005. This COSHH assessment addresses the use of Hammerite Direct to Rust Metal Paint (solvent-based alkyd resin coating) and Hammerite Brush Cleaner (hydrocarbon/xylene solvent mixture) in industrial, commercial, and maintenance environments. Both products are classified as flammable liquids (Category 3) and present inhalation hazards from volatile organic compounds including xylene, white spirit, and aromatic hydrocarbons. The assessment covers application by brush, roller, or spray; surface preparation; equipment cleaning; and waste disposal. Compliance requires engineering controls (LEV with minimum 0.5 m/s capture velocity), DSEAR zoning (Zone 2 where vapour may form), health surveillance for xylene exposure, and strict ignition source control within 5 metres of work area.

Statutory FrameworkCOSHH Regulations 2002, DSEAR 2002, EH40/2005 Solvent Vapour WELs (GHS02 H226, GHS07 H336)
Classification**GHS/CLP Classification:** - GHS02 Flame: H226 Flammable liquid and vapour (Category 3) - GHS07 Exclamation Mark: H336 May cause drowsiness or dizziness (STOT SE Category 3 - Narcotic effects) - H304 May be fatal if swallowed and enters airways (Aspiration Hazard Category 1) - H319 Causes serious eye irritation (Eye Irritation Category 2) - H335 May cause respiratory irritation - H411 Toxic to aquatic life with long lasting effects **Hazardous Substances:** - Xylene (mixed isomers): 10-25% w/w, CAS 1330-20-7, WEL 50 ppm (220 mg/m³) 8-hr TWA, 100 ppm (441 mg/m³) 15-min STEL - Hydrocarbons, C9-C11, n-alkanes, isoalkanes, cyclics, <2% aromatics (White Spirit): 25-50% w/w, WEL 850 mg/m³ 8-hr TWA, 1200 mg/m³ 15-min STEL - Naphtha (petroleum), hydrotreated heavy: 10-25% w/w - Solvent naphtha (petroleum), light aromatic: <10% w/w **DSEAR Classification:** Flammable liquid, Flash point 32-38°C (closed cup). Workplace requires Zone 2 classification where flammable vapour/air mixture may form during normal operation. Ignition sources must be eliminated within 5m radius of application/cleaning activities. **UN Transport:** UN 1263 PAINT or UN 1263 PAINT RELATED MATERIAL, Class 3 Flammable Liquid, Packing Group III
Required Plant / KitLocal Exhaust Ventilation (LEV) system with minimum 0.5 m/s capture velocity at source, tested and examined every 14 months per COSHH Regulation 9 and HSG258 • Intrinsically safe (ATEX-certified) electrical equipment rated for Zone 2 hazardous areas per DSEAR 2002 and BS EN 60079 series • Sealed metal waste containers with self-closing lids (UN-approved for Class 3 flammable liquids) for contaminated rags and waste • Explosion-proof or air-powered spray equipment (if spray application used) with earthing/bonding cables to prevent static discharge • Calibrated direct-reading personal air sampling pumps and xylene/hydrocarbon vapour detection tubes or photoionisation detector (PID) for exposure monitoring per COSHH Regulation 10
Site Sign-Off StatusRequires Competent Person Verification
Instant AI Customization or Free Blank Word (.doc) Download

Need this COSHH customized with your Company Name, Site Postcode & Nearest A&E Hospital?

Dictate your site specifics on your phone in 45 seconds to auto-compile a signed PDF—or download our free blank Word (.doc) shell below.

Auto-Fill via Voice / CLP (45s)

1. Mandatory Personal Protective Equipment (BS EN Standards)

BS EN ISO 374-1:2016/A1:2018 Type B (KPT), BS EN 374-4:2013 (degradation resistance to xylene and aromatic hydrocarbons)
Nitrile chemical-resistant gloves (minimum 0.38mm thickness, breakthrough time >480 minutes for xylene)
Mandatory to prevent dermal absorption of xylene and hydrocarbon solvents which can cause defatting dermatitis and systemic toxicity. Latex and vinyl gloves offer inadequate protection. Replace gloves every 2 hours or immediately if contaminated.
BS EN 140:1999 half-mask with BS EN 14387:2004+A1:2008 Class A (brown) organic vapour filter and BS EN 143:2021 P2 particulate filter
Organic vapour respirator (A1P2 or A2P2 combined filter) or supplied-air breathing apparatus for confined spaces
Mandatory where LEV cannot reduce xylene vapour below 50 ppm TWA or during spray application. A1 filter protects against organic vapours <1000 ppm, A2 for <5000 ppm. Face-fit testing required per HSE INDG479. Replace filters per manufacturer schedule or when solvent odour detected.
BS EN 166:2001 Frame marking F (low energy impact), Lens marking 2C-1.2 (liquid droplet protection, UV filter, optical class 1 or 2)
Safety spectacles with side shields or full-face visor (if splash risk during pouring/mixing)
Mandatory to prevent eye contact with liquid causing serious irritation (H319). Xylene and hydrocarbon solvents cause immediate stinging, lacrimation, and corneal damage. Full-face visor required for spray application or overhead work.
BS EN ISO 20345:2011 S3 (steel toecap, penetration-resistant midsole, antistatic, energy absorption, hydrocarbon-resistant outsole, water-resistant upper)
Chemical-resistant safety footwear with anti-static properties and hydrocarbon-resistant sole
Mandatory in DSEAR Zone 2 areas to dissipate static electricity and prevent ignition of flammable vapours. Hydrocarbon-resistant sole prevents degradation from solvent spills. Antistatic footwear (resistance 100 kΩ to 1000 MΩ) required per BS EN 61340-5-1.

2. 5×5 Hazard Risk Assessment Matrix (HASAWA 1974 / MHSWR 1999)

Identified Hazard & HarmInitial Risk (L×S)Mandatory Engineering, Isolation & Procedural ControlsResidual Risk
1. Inhalation of xylene and hydrocarbon solvent vapours during paint application, brush cleaning, and drying phase
Harm: Acute: Dizziness, headache, nausea, respiratory irritation, narcotic effects (CNS depression) per H336. Chronic: Neurotoxicity, liver and kidney damage from repeated xylene exposure above WEL. Exceeding 50 ppm TWA or 100 ppm STEL violates EH40/2005 limits.
4 × 4 = 16Engineering: Install and operate LEV system with minimum 0.5 m/s capture velocity at source, tested every 14 months per HSG258. Conduct personal air monitoring using calibrated sampling pumps and xylene-specific detection (MDHS 88 or equivalent) to verify exposure <50% WEL. Administrative: Implement health surveillance (questionnaire and biological monitoring - urinary methylhippuric acid) for workers exposed >50% WEL per COSHH Regulation 11. Rotate tasks to limit individual exposure duration. PPE: Mandatory A1P2 or A2P2 organic vapour respirator where LEV inadequate or during spray application. Ensure face-fit testing per INDG479. Provide natural ventilation (open doors/windows) as secondary control. Prohibit work in confined spaces without supplied-air BA and permit-to-work.3 × 2 = 6
2. Fire and explosion risk from flammable vapours (flash point 32-38°C) in presence of ignition sources
Harm: Catastrophic fire or vapour explosion causing severe burns, fatalities, and structural damage. Flammable vapour/air mixture forms readily at ambient temperatures (>20°C) creating DSEAR Zone 2 hazardous area. Lower explosive limit (LEL) for xylene is 1.0% v/v.
3 × 5 = 15DSEAR Assessment: Classify work area as Zone 2 (5m radius from application/cleaning point). Eliminate ignition sources: prohibit smoking, naked flames, hot work within 10m. Isolation: De-energise and lock-out non-ATEX electrical equipment per BS 7671. Use only intrinsically safe tools and ATEX-certified equipment rated Ex II 3G for Zone 2. Bonding/Earthing: Earth all metal containers and spray equipment to prevent static discharge (resistance <10Ω to earth per BS EN 61340-5-1). Ventilation: Maintain LEV to keep vapour concentration <10% LEL (monitored by PID or catalytic bead sensor). Housekeeping: Store max 50 litres in DSEAR-compliant flammable liquid cabinet. Dispose of solvent-soaked rags in sealed metal waste bins emptied daily. Emergency: Provide CO₂ or foam fire extinguishers (not water). Train operatives in emergency shutdown and evacuation per fire risk assessment.2 × 4 = 8
3. Skin contact causing defatting dermatitis, irritation, and systemic absorption of xylene
Harm: Acute: Skin redness, dryness, cracking, and pain from solvent defatting. Prolonged contact allows dermal absorption of xylene leading to systemic toxicity (CNS effects, liver/kidney damage). Chronic: Occupational contact dermatitis requiring medical treatment and work restriction.
5 × 3 = 15Elimination: Use brush or roller application in preference to spray to minimise skin contact. Substitution: Not feasible - water-based alternatives lack rust-inhibiting properties for direct-to-rust application. Engineering: Provide wash stations with warm water, mild soap, and skin-conditioning cream within 10m of work area. PPE: Mandatory nitrile gloves (0.38mm, breakthrough >480 min for xylene) per BS EN ISO 374-1:2016 Type B (KPT). Inspect gloves before each use; replace every 2 hours or immediately if contaminated. Wear long-sleeved coveralls (Type 6 chemical-resistant per BS EN 13034:2005+A1:2009 if heavy contamination risk). Administrative: Train operatives in correct glove donning/doffing to avoid contamination. Prohibit eating, drinking, smoking in work area. Implement pre-work skin checks and health surveillance for dermatitis. Provide barrier creams (pre-work) and after-work moisturisers. Emergency: If skin contact occurs, remove contaminated clothing immediately and wash with soap and water for 15 minutes.4 × 2 = 8
4. Eye contact with liquid paint or brush cleaner causing serious irritation (H319)
Harm: Immediate stinging, lacrimation, redness, and blurred vision. Xylene and aromatic hydrocarbons cause corneal epithelial damage. Untreated exposure may result in prolonged discomfort and temporary vision impairment requiring medical treatment.
4 × 3 = 12Engineering: Install emergency eyewash station (BS EN 15154-2:2006 compliant) within 10 seconds travel time of work area. Test weekly and record in logbook. Substitution: Use brush/roller application to minimise splash risk; avoid spray application where practicable. PPE: Mandatory safety spectacles with side shields (BS EN 166:2001 marking F, 2C-1.2) for all paint handling and brush cleaning. Upgrade to full-face visor (BS EN 166 marking 3) for spray application, overhead work, or pouring from bulk containers. Administrative: Train operatives in emergency eyewash procedure (15-minute continuous irrigation while holding eyelids open). Prohibit contact lens wear during solvent handling. Supervision: Ensure buddy system for lone workers to assist in emergency. Emergency: Irrigate eyes immediately for 15 minutes, remove contact lenses after 5 minutes if present, seek medical attention even if irritation subsides.3 × 2 = 6
5. Aspiration hazard if swallowed and enters airways (H304) causing chemical pneumonitis
Harm: Fatal or life-threatening chemical pneumonitis if vomited product enters lungs. Hydrocarbon solvents have low viscosity and high spreading coefficient, causing rapid lung damage, pulmonary oedema, and respiratory failure. Medical emergency requiring immediate hospitalisation.
2 × 5 = 10Elimination: Decant only the required quantity into smaller containers to minimise volume at work face and reduce ingestion risk. Engineering: Use containers with child-resistant closures and restricted openings to prevent accidental ingestion. Label all decanted containers with GHS pictograms and H304 warning. Administrative: Prohibit eating, drinking, and smoking in work area. Enforce hand-washing before breaks. Store products in locked cabinet away from food/drink areas. Train operatives: DO NOT INDUCE VOMITING if swallowed - this is critical as vomiting increases aspiration risk. Supervision: Implement permit-to-work for confined space application where rescue may be delayed. Emergency: If swallowed, rinse mouth with water, do NOT induce vomiting, place casualty in recovery position if unconscious, call 999 immediately and inform paramedics of H304 aspiration hazard. Transport product SDS to hospital. Monitor for respiratory distress (coughing, choking, breathing difficulty) for 48 hours post-exposure.1 × 5 = 5

3. Step-by-Step Safe Sequence of Operations & Hold-Points

Emergency Rescue, First Aid & Spill Protocol

4. UK HSE Compliance FAQs: Hammerite Direct to Rust Metal Paint & Brush Cleaner (Hydrocarbon / Xylene)

5. Operative Toolbox Talk & Competent Person Sign-Off Register

Competent Person & Operative Declaration: By signing below, the Site Supervisor confirms this assessment has been adapted and verified for actual site conditions, and operatives confirm they have attended the pre-start Toolbox Talk for Hammerite Direct to Rust Metal Paint & Brush Cleaner (Hydrocarbon / Xylene) and will follow the safe system of work.

Operative / Supervisor Name Trade / Role & CSCS No. Signature Date & Time
1. (Site Supervisor):     
2.     
3.     
4.     
5.     
6.     

Related UK Safety Templates & Risk Assessments