SafeSequence › UK Safety Template Library › COSHH & Chemical Safety › Caustic Soda Pearl & Liquid Lye (Sodium Hydroxide 32-50%) CIP Cleaning
Verified UK COSHH Standard • COSHH & Chemical Safety

Caustic Soda Pearl & Liquid Lye (Sodium Hydroxide 32-50%) CIP Cleaning (COSHH Template & 5x5 Risk Assessment)

This COSHH assessment covers the safe handling, storage, and use of caustic soda pearl and liquid lye (sodium hydroxide 32-50% concentration) during Clean-In-Place (CIP) cleaning operations in food processing, pharmaceutical, and industrial facilities. Sodium hydroxide is classified as GHS05 Corrosive and presents severe hazards including skin corrosion (Category 1A), serious eye damage (Category 1), and respiratory irritation. The UK Workplace Exposure Limit (WEL) is 2 mg/m³ (STEL) as per EH40/2005. This document establishes mandatory engineering controls, LOTO procedures, emergency response protocols, and competency requirements to ensure compliance with COSHH Regulations 2002 (as amended). All personnel must complete COSHH training and demonstrate competence before handling sodium hydroxide. Emergency eyewash stations and safety showers must be located within 10 seconds travel time of all handling areas.

Statutory FrameworkCOSHH Regulations 2002, EH40/2005 WEL (2 mg/m3 STEL), CLP Regulation (GHS05 Corrosive)
ClassificationUN Number: UN1823 (Sodium hydroxide, solid) / UN1824 (Sodium hydroxide solution). GHS Classification: Skin Corrosion Category 1A (H314 - Causes severe skin burns and eye damage), Serious Eye Damage Category 1 (H318 - Causes serious eye damage). Signal Word: DANGER. GHS Pictogram: GHS05 (Corrosion). CLP Regulation (EC) No 1272/2008 applies. Precautionary Statements: P280 (Wear protective gloves/protective clothing/eye protection/face protection), P301+P330+P331 (IF SWALLOWED: Rinse mouth. Do NOT induce vomiting), P303+P361+P353 (IF ON SKIN: Remove immediately all contaminated clothing. Rinse skin with water), P305+P351+P338 (IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing), P310 (Immediately call a POISON CENTRE or doctor). Storage: Store in corrosion-resistant containers with resistant inner liner. Keep container tightly closed in a cool, well-ventilated place. Segregate from acids, aluminium, zinc, and organic materials.
Required Plant / KitCIP (Clean-In-Place) automated dosing system with interlocked controls and flow monitoring • Corrosion-resistant chemical transfer pump (316 stainless steel or PVDF) with mechanical seal • pH monitoring equipment with calibrated probes and data logging capability • Emergency eyewash station (BS EN 15154-2:2006) and deluge safety shower (BS EN 15154-1:2006) within 10 seconds travel time • Lockout/Tagout (LOTO) devices including valve locks, electrical lockout hasps, and danger tags conforming to BS EN ISO 14118
Review Cycle12 Months / Post-Incident
Instant AI Customization or Free Blank Word (.doc) Download

Need this COSHH customized with your Company Name, Site Postcode & Nearest A&E Hospital?

Dictate your site specifics on your phone in 45 seconds to auto-compile a signed PDF—or download our free blank Word (.doc) shell below.

Auto-Fill via Voice / CLP (45s)

2. 5×5 Hazard Risk Assessment Matrix (HASAWA 1974 / MHSWR 1999)

Identified Hazard & Harm Initial Risk (L×S) Mandatory Engineering, Isolation & Procedural Controls Residual Risk
1. Severe skin corrosion and chemical burns from direct contact with sodium hydroxide solution (32-50%)
Harm: Deep tissue burns (Category 1A corrosive), permanent scarring, tissue necrosis requiring surgical debridement, potential systemic toxicity if large area affected. Burns may not be immediately painful but cause progressive deep tissue damage.
5 × 5 = 25 Engineering: Fully enclosed CIP system with automated dosing eliminates manual handling. Administrative: LOTO procedures mandatory during maintenance. Permit-to-Work system for all interventions. PPE: Type A chemical gloves (BS EN ISO 374-1), Type 3/4 coveralls (BS EN 14605), face shield (BS EN 166). Emergency shower within 10 seconds. Competency: COSHH training and practical assessment required. Refresher every 12 months. 3 × 4 = 12
2. Serious irreversible eye damage from splashes or aerosol mist during transfer, sampling, or system breaches
Harm: Permanent blindness, corneal opacity, complete destruction of ocular tissue, irreversible damage within 15 seconds of contact. Even dilute solutions (>5%) cause severe injury.
4 × 5 = 20 Engineering: Closed-loop CIP system with pressure relief valves and leak detection. Sample points designed with drip trays and splash guards. Administrative: Pre-use system pressure checks. Two-person rule for sampling operations. PPE: Full-face shield or chemical goggles (BS EN 166:2001, 3-1.2.3.9 marking) mandatory. Emergency eyewash (BS EN 15154-2) tested weekly. Competency: Emergency eyewash drill quarterly. First aiders trained in chemical eye irrigation (minimum 15 minutes continuous flushing). 2 × 5 = 10
3. Inhalation of sodium hydroxide aerosol or mist causing respiratory tract burns and pulmonary oedema
Harm: Chemical pneumonitis, laryngeal oedema, bronchospasm, delayed pulmonary oedema (up to 48 hours post-exposure), permanent respiratory impairment. WEL: 2 mg/m³ STEL (EH40/2005).
3 × 4 = 12 Engineering: Local Exhaust Ventilation (LEV) at all potential emission points (minimum 10 air changes/hour). Enclosed transfer systems prevent aerosol generation. Administrative: LEV thorough examination every 14 months (COSHH Regulation 9). Air monitoring at 6-month intervals with results <50% WEL action level. Respiratory protection (FFP3 or half-mask with A2-P3 filters to BS EN 149/BS EN 140) for emergency response only. Competency: Fit-testing for RPE users. Medical surveillance for respiratory symptoms. 2 × 3 = 6
4. Exothermic reaction and violent boiling when sodium hydroxide contacts water or acids during dilution or neutralisation
Harm: Thermal burns from heat generation (up to 90°C), explosive boiling causing widespread splashing, pressurisation of closed systems leading to rupture, projection of corrosive liquid over wide area.
4 × 4 = 16 Engineering: Automated dilution systems with temperature monitoring and interlocks. Always add caustic to water, never water to caustic (controlled addition rate <5 L/min). Pressure relief valves set at 1.5 bar. Administrative: Written dilution procedures with step-by-step instructions. Segregated storage (minimum 3m separation from acids). Incompatibility matrix displayed. LOTO during tank cleaning. Competency: Practical demonstration of dilution procedure. Understanding of exothermic hazards. Spill response training. 2 × 3 = 6
5. Corrosion of plant equipment, pipework, and containment leading to catastrophic failure and major chemical release
Harm: Large-scale environmental contamination, multiple casualties from widespread exposure, damage to drainage systems (pH >12.5 causing concrete degradation), regulatory enforcement action, business interruption.
3 × 5 = 15 Engineering: 316 stainless steel or PVDF construction for all wetted parts. Corrosion monitoring via ultrasonic thickness testing annually. Secondary containment (110% capacity) with pH-resistant coating. Leak detection systems with automatic shutdown. Administrative: Planned preventive maintenance schedule. Pre-use visual inspections (daily). Pressure testing after maintenance (1.5x operating pressure). COMAH/RIDDOR reporting procedures. Competency: Authorised Person (Mechanical) for pressure system inspections. Written Scheme of Examination under PSSR 2000. Emergency response team trained in large-scale chemical spill containment. 1 × 4 = 4

3. Step-by-Step Safe Sequence of Operations & Hold-Points

1

System Isolation, LOTO Application, and Pre-Use Verification

Preparation and Pre-Operational Checks

Verify CIP system is isolated from production equipment. Apply LOTO to all energy sources (electrical, pneumatic, hydraulic) using group lockout box if multiple personnel involved. Verify zero energy state using voltage tester and pressure gauges. Inspect all PPE for damage (gloves for perforations, face shield for cracks, boots for chemical damage). Confirm emergency eyewash and safety shower are operational (activate for 5 seconds to verify flow). Check sodium hydroxide concentration using calibrated pH meter or titration (target 32-50%). Verify LEV system is operational (minimum face velocity 1 m/s at emission points). Review SDS and emergency procedures. Confirm second person is available for duration of task (two-person rule).

Critical Hold-Point: CRITICAL HOLD POINT: Do NOT proceed until LOTO is verified by Authorised Person and all PPE is confirmed serviceable. Sodium hydroxide causes irreversible burns within seconds - emergency equipment MUST be functional before starting. Verify concentration - solutions >50% have increased viscosity and corrosivity requiring modified procedures.
2

Automated Dosing System Activation and Concentration Verification

Chemical Transfer and System Charging

Don all mandatory PPE in correct sequence: coveralls, boots, gloves (inspect for defects), face shield. Position drip trays under all connection points. Open caustic supply valve slowly (quarter-turn increments) to prevent pressure surge. Activate automated dosing pump at minimum flow rate initially. Monitor pressure gauges (normal operating range 2-4 bar). Verify flow rate using calibrated flow meter. Check for leaks at all flanged connections, valve glands, and pump seals using visual inspection (do NOT use hands). If leak detected, immediately shut down system, depressurise, and re-apply LOTO before investigation. Record start time, concentration, temperature, and flow rate in CIP log. Verify pH monitoring system is recording data.

Critical Hold-Point: CRITICAL HOLD POINT: If ANY leak is detected, execute emergency shutdown immediately. Do NOT attempt to tighten connections under pressure. Evacuate immediate area and activate emergency response. Pressure surges can cause catastrophic seal failure - always open valves slowly. Maintain minimum 1 metre distance from all pressurised connections.
3

Monitoring Cleaning Parameters and System Integrity During Circulation

CIP Cleaning Cycle Operation

Monitor CIP control panel for temperature (target 70-85°C), concentration (maintain 1.5-3% in circulation), and contact time (typically 20-30 minutes). Verify circulation flow rate remains within specification (typically 1.5-2 m/s velocity). Conduct visual inspection of accessible pipework every 10 minutes for signs of leakage, excessive vibration, or unusual noise. Monitor LEV system performance (check manometer readings against baseline). Record pH, temperature, and conductivity at 5-minute intervals. If parameters drift outside specification, investigate cause before continuing. Check secondary containment areas for any accumulation. Maintain communication with second person throughout operation. Do NOT leave system unattended during caustic circulation phase.

Critical Hold-Point: CRITICAL HOLD POINT: If temperature exceeds 90°C or pressure exceeds 6 bar, initiate emergency shutdown immediately - risk of system rupture and explosive boiling. If circulation flow drops below 50% of normal, stop immediately and investigate blockage. Never attempt to clear blockages while system is pressurised or contains caustic.
4

Caustic Displacement, Neutralisation, and Water Rinse Verification

Neutralisation and Rinse Cycle

Upon completion of cleaning cycle, initiate water displacement rinse. Divert caustic return to recovery tank (if system equipped) or neutralisation tank. Begin water rinse at same flow rate as cleaning cycle. Monitor pH continuously - target pH <11 before discharge to drain (check local trade effluent consent limits). If neutralisation required, add acid slowly via automated dosing system (never add manually). Continue rinsing until pH stabilises at 6-8 for minimum 5 minutes. Collect final rinse sample for pH verification using calibrated meter. Record total rinse volume and final pH in CIP log. Verify conductivity has returned to baseline (typically <500 µS/cm). Check all drain points are flowing freely.

Critical Hold-Point: CRITICAL HOLD POINT: Never discharge caustic solution with pH >11 to drain without authorisation - risk of drainage system damage and environmental prosecution. If neutralising with acid, add acid to caustic slowly with continuous agitation - NEVER add caustic to acid. Monitor temperature during neutralisation - exothermic reaction can cause boiling. Verify pH before discharge - single reading insufficient, require stable pH for 5 minutes minimum.
5

Safe Depressurisation, Drainage, and Equipment Decontamination

System Shutdown and Decontamination

Close caustic supply valve and stop dosing pump. Depressurise system slowly using vent valves (open quarter-turn every 30 seconds to prevent surge). Verify zero pressure on all gauges before proceeding. Drain residual liquid to designated collection point - never to open drain. Flush all sample points and drain valves with water. If system requires opening for maintenance, conduct final water flush (minimum 10 minutes) and verify pH <9 at all drain points. Decontaminate all tools and equipment using water rinse followed by neutralising solution if required. Inspect all PPE for contamination - if contaminated, rinse thoroughly with water before removal. Remove PPE in correct sequence (gloves last) and dispose of/decontaminate as per site procedures.

Critical Hold-Point: CRITICAL HOLD POINT: Never assume system is caustic-free based on rinse cycle alone. Always verify pH at multiple sample points before opening system. Residual caustic in dead-legs, valve pockets, or low points can cause severe burns. Maintain full PPE until pH verification complete. If opening system for maintenance, wait minimum 30 minutes after final rinse to allow drainage and cooling.
6

Record Completion, Incident Reporting, and Controlled Return to Service

Post-Operation Documentation and LOTO Removal

Complete CIP cleaning record including: start/end times, chemical concentrations, temperatures, pH readings, rinse volumes, any deviations from procedure, and personnel involved. Report any near-misses, equipment defects, or procedural difficulties via site incident reporting system. Inspect all equipment for damage or wear - record findings and initiate maintenance requests if required. Verify all drain valves are closed and system is secure. Remove LOTO devices only after confirming system is safe to return to service and all personnel are clear. Conduct post-task debrief with second person to identify improvements. Store all PPE correctly (hang gloves to dry, inspect face shield for damage). Update chemical inventory records. File completed documentation in COSHH assessment folder. Schedule next LEV examination if due within 3 months.

Critical Hold-Point: CRITICAL HOLD POINT: Only the person who applied LOTO may remove their own lock - never remove another person's lock. Verify all personnel are accounted for and clear of equipment before removing group lockout. Do NOT return system to production use until pH verification is documented and approved by supervisor. Incomplete documentation may indicate incomplete procedure - investigate before proceeding.

Emergency Rescue, First Aid & Spill Protocol

EMERGENCY RESPONSE PROCEDURES: In event of major spill (>10 litres), activate site emergency alarm and evacuate non-essential personnel. Establish 10-metre exclusion zone. Notify emergency services if public risk exists. Emergency response team must wear full chemical PPE (Type 3 suit, full-face respirator with A2-P3 filters, chemical boots and gloves). Contain spill using absorbent booms and neutralise with weak acid (acetic acid 5-10%) or CO2. Never use water on concentrated spills - causes violent exothermic reaction. Collect neutralised material in sealed containers for disposal as hazardous waste (EWC code 06 02 01). Flush residues with copious water. Report to Environment Agency if spill enters watercourse (incident hotline 0800 807060). RIDDOR report required if injury results. FIRST AID - SKIN CONTACT: Remove victim from exposure immediately. Remove contaminated clothing while flushing with water (cut off if necessary - do NOT pull over head). Flush affected area with copious running water for minimum 15 minutes (continue during transport if necessary). Do NOT attempt to neutralise on skin. Cover burns with sterile non-adherent dressing. Seek immediate medical attention - all caustic burns require hospital assessment even if appear minor. Provide SDS to medical personnel. FIRST AID - EYE CONTACT: Hold eyelids open and flush with lukewarm water for minimum 15 minutes using emergency eyewash. Remove contact lenses if present and easy to do - continue flushing. Do NOT use neutralising agents in eyes. Call 999 immediately - eye injuries are medical emergencies requiring immediate ophthalmology assessment. Continue flushing during transport. Permanent blindness can result from delayed treatment. FIRST AID - INHALATION: Remove victim to fresh air immediately. Keep at rest in semi-upright position. If breathing is difficult, administer oxygen if trained and available. Do NOT induce vomiting if swallowed. Call 999 immediately. Monitor for delayed pulmonary oedema (up to 48 hours) - all inhalation exposures require hospital observation. Provide SDS to paramedics. FIRST AID - INGESTION: Rinse mouth thoroughly with water. Do NOT induce vomiting - risk of oesophageal perforation. Give small amounts of water to drink if conscious (maximum 200ml). Do NOT attempt to neutralise. Call 999 immediately and transport to hospital. This is a life-threatening emergency requiring immediate medical intervention. Provide SDS to medical personnel. DECONTAMINATION: Contaminated PPE must be rinsed with copious water before removal. Dispose of heavily contaminated items as hazardous waste. Wash hands and face thoroughly after PPE removal even if no known contact. Shower and change clothing if significant exposure suspected. Contaminated clothing must be laundered separately or disposed of as hazardous waste.

4. UK HSE Compliance FAQs: Caustic Soda Pearl & Liquid Lye (Sodium Hydroxide 32-50%) CIP Cleaning

5. Operative Toolbox Talk & Competent Person Sign-Off Register

Competent Person & Operative Declaration: By signing below, the Site Supervisor confirms this assessment has been adapted and verified for actual site conditions, and operatives confirm they have attended the pre-start Toolbox Talk for Caustic Soda Pearl & Liquid Lye (Sodium Hydroxide 32-50%) CIP Cleaning and will follow the safe system of work.

Operative / Supervisor Name Trade / Role & CSCS No. Signature Date & Time
1. (Site Supervisor):     
2.     
3.     
4.     
5.     
6.     

Related UK Safety Templates & Risk Assessments