SafeSequence › UK Safety Template Library › Commercial Brand COSHH › Fernox F1 Protector, F3 Cleaner & DS40 Commercial Heating Descaler
Reference UK COSHH Example • Commercial Brand COSHH

Fernox F1 Protector, F3 Cleaner & DS40 Commercial Heating Descaler (COSHH Template & 5x5 Risk Assessment)

Under COSHH Regulations 2002, UK CLP Regulation (Eye & Skin Irritation Controls), and BS 7593, employers must assess, control, and monitor exposure to Fernox F1 Protector, F3 Cleaner, and DS40 Commercial Heating Descaler through engineering controls, isolation of pressurised systems, and mandatory PPE to reduce dermal/ocular contact risk from ≥12 (medium-high) to ≤6 (tolerable). These chemical treatment products contain corrosion inhibitors, alkaline cleaning agents, and acidic descaling compounds requiring specific handling protocols to prevent chemical burns, respiratory irritation, and environmental contamination in commercial heating system maintenance operations.

Statutory FrameworkCOSHH Regulations 2002, UK CLP Regulation (Eye & Skin Irritation Controls), BS 7593
ClassificationFernox F1 Protector: GHS Classification - Not classified as hazardous under UK CLP. Contains inhibitors and dispersants. Fernox F3 Cleaner: GHS05 Corrosion, GHS07 Irritant. Causes skin irritation (H315) and serious eye damage (H318). Contains sodium metasilicate. pH 11-13 (alkaline). Fernox DS40 Commercial Descaler: GHS05 Corrosion, GHS07 Irritant. Causes severe skin burns and eye damage (H314). Contains sulphamic acid and organic acids. pH 1-2 (acidic). UN3265 (Corrosive liquid, acidic, organic, n.o.s.) for DS40. Store segregated per BS 7593. Emergency contact: National Poisons Information Service 0344 892 0111.
Required Plant / KitFernox TF1 Total Filter or magnetic filter for system protection • Calibrated dosing pump or measuring vessel (graduated to 100ml) for accurate chemical addition • Lockable isolation valves with LOTO capability on system fill/drain points • Chemical-resistant transfer pump (polypropylene or PVDF construction) rated for pH 1-14 • Sealed chemical storage cabinet compliant with BS 7593 with spill containment bund (110% capacity)
Site Sign-Off StatusRequires Competent Person Verification
Instant AI Customization or Free Blank Word (.doc) Download

Need this COSHH customized with your Company Name, Site Postcode & Nearest A&E Hospital?

Dictate your site specifics on your phone in 45 seconds to auto-compile a signed PDF—or download our free blank Word (.doc) shell below.

Auto-Fill via Voice / CLP (45s)

1. Mandatory Personal Protective Equipment (BS EN Standards)

BS EN ISO 374-1:2016/A1:2018 Type B (minimum 480 min breakthrough for acids/alkalis)
Chemical-resistant gloves (nitrile or neoprene)
Mandatory protection against skin irritation (H315) from F3 Cleaner and severe burns (H314) from DS40 acidic descaler during dosing, system filling, and drain-down operations
BS EN 166:2001 Grade 3 liquid splash protection
Safety goggles or full-face shield
Essential eye protection against serious eye damage (H318) from alkaline F3 Cleaner and corrosive DS40 descaler splashes during chemical transfer and system venting
BS EN 14605:2005 Type 4 liquid-tight protection
Chemical-resistant apron or coveralls
Prevents dermal exposure to corrosive liquids during bulk dosing, system flushing, and emergency spill response as required by COSHH ACoP L5
BS EN ISO 20345:2011 S5 (penetration resistant, antistatic, energy absorption)
Safety footwear with chemical-resistant properties
Protects against floor-level spills of acidic DS40 and alkaline F3 products in plant rooms and confined spaces during heating system maintenance

2. 5×5 Hazard Risk Assessment Matrix (HASAWA 1974 / MHSWR 1999)

Identified Hazard & HarmInitial Risk (L×S)Mandatory Engineering, Isolation & Procedural ControlsResidual Risk
1. Severe skin burns and eye damage from DS40 Commercial Descaler (pH 1-2, sulphamic acid)
Harm: Chemical burns to skin, permanent eye damage, scarring requiring hospital treatment
4 × 3 = 12Isolate heating system and depressurise to <0.5 bar before chemical addition. Use closed-loop dosing pump to eliminate manual handling. Enforce BS EN ISO 374-1:2016 gloves and BS EN 166 face shield as permit-to-work condition. Provide eyewash station within 10m per BS EN 15154. Segregate acidic DS40 from alkaline F3 per BS 7593 (minimum 3m separation). Implement two-person working for bulk transfers >5L.2 × 2 = 4
2. Serious eye damage (H318) from alkaline F3 Cleaner splashback during system venting
Harm: Corneal burns, permanent vision impairment, lost-time injury
3 × 4 = 12Install automatic air vents (AAVs) to eliminate manual venting. Where manual venting required, use shielded vent keys and enforce face shield use. Reduce system pressure to <1 bar before venting. Position operator below vent point. Provide BS EN 15154-2 eyewash with 15-minute supply. Train operatives in emergency eye irrigation procedure per COSHH ACoP L5 paragraph 127.2 × 3 = 6
3. Inhalation of acidic vapours/mists from DS40 in confined plant rooms (poor ventilation)
Harm: Respiratory tract irritation, coughing, breathing difficulty, occupational asthma
3 × 3 = 9Conduct atmospheric monitoring pre-entry (O2 >19.5%, no acid vapour detection). Provide mechanical ventilation achieving 6 air changes/hour minimum. Use closed-transfer systems for DS40 dosing. Implement confined space entry procedures per BS 7671. Provide FFP3 respirators (BS EN 149:2001+A1:2009) for emergency use. Prohibit hot work during/after descaling (vapour generation risk).2 × 2 = 4
4. Exothermic reaction and pressure surge from mixing incompatible Fernox products (acid/alkali)
Harm: Violent chemical reaction, system rupture, scalding, chemical spray injuries
2 × 4 = 8Enforce strict product sequencing: F3 Cleaner flush → drain → neutralise → F1 Protector. Never mix DS40 (acidic) with F3 (alkaline). Implement colour-coded dosing equipment (red=acid, blue=alkali). Lock-off dosing points between stages using LOTO padlocks. Verify pH neutrality (6-8) via test strips before product changeover. Display chemical compatibility matrix at dosing stations.1 × 3 = 3
5. Environmental contamination from uncontrolled discharge of chemically treated water to drains
Harm: Watercourse pollution, prosecution under Environmental Protection Act 1990, fines up to £50,000
3 × 3 = 9Discharge only to foul sewer (not surface water drains). Neutralise DS40-treated water to pH 6-9 using soda ash before discharge. Install interceptor tank with pH monitoring. Obtain trade effluent consent from water authority for commercial volumes. Collect first flush in bunded IBC for licensed disposal. Implement spill kits (50L absorbent capacity) at all dosing points per PPG6 guidance.1 × 2 = 2

3. Step-by-Step Safe Sequence of Operations & Hold-Points

1

System Isolation, LOTO Application & Pre-Use Checks

Preparation & Isolation

Isolate heating system at main isolating valves and depressurise to <0.5 bar via drain cock. Apply LOTO padlocks to isolation valves and tag with permit number. Verify Fernox product batch numbers match SDS issue dates. Check eyewash station functionality (15-minute flow test). Don full PPE (chemical gloves, face shield, apron, S5 boots) before opening chemical containers. Confirm mechanical ventilation operational (6 ACH minimum) in plant room. Segregate DS40 (acidic) and F3 (alkaline) products with 3m minimum separation per BS 7593.

Critical Hold-Point: HOLD POINT: Do not proceed until LOTO is verified by second competent person and atmospheric monitoring confirms safe conditions (O2 >19.5%, no vapour detection). Mixing acidic and alkaline products causes violent exothermic reaction.
2

Alkaline Cleaner Addition & Circulation

Chemical Dosing - F3 Cleaner

Calculate F3 Cleaner dose: 1% system volume for light fouling, 2% for heavy scale (e.g. 10L per 1000L system). Use calibrated measuring vessel or closed-loop dosing pump. Add F3 via system fill point with face shield in position. Pressurise system slowly to 1.5 bar. Circulate at 60-80°C for minimum 1 hour (light fouling) or up to 7 days (heavy deposits) per manufacturer's datasheet. Monitor pH weekly using test strips (target pH 10-12 indicates active cleaning).

Critical Hold-Point: CRITICAL: F3 Cleaner is alkaline (pH 11-13) and causes serious eye damage (H318). Maintain face shield throughout dosing. Never heat above 85°C (accelerated corrosion risk). Do not add DS40 descaler until F3 is fully drained and neutralised.
3

F3 Cleaner Drain-Down & pH Neutralisation

Drain & Neutralisation

Cool system to <40°C before draining. Open drain cock slowly to prevent splashback. Discharge F3-treated water to foul sewer only (not surface water). Test pH of discharged water—if pH >9, neutralise using citric acid or vinegar to pH 6-8 before discharge. Flush system with mains water (minimum 2 system volumes) until discharge pH is neutral (6-8). Verify complete drainage at low points and radiators. Inspect drain water for debris/sludge indicating cleaning effectiveness.

Critical Hold-Point: HOLD POINT: Verify pH neutrality (6-8) using calibrated test strips before proceeding to descaling stage. Residual alkalinity will neutralise DS40 descaler and prevent effective scale removal. Obtain pH reading from second person for verification.
4

Acidic Descaler Addition for Heavy Scale Removal

Chemical Dosing - DS40 Descaler (if required)

For systems with heavy limescale (hardness >200ppm CaCO3), dose DS40 Commercial Descaler at 5-10% system volume. Use dedicated acidic-product dosing pump (never reuse F3 equipment). Add DS40 via fill point with full face shield and Type B chemical gloves. Circulate at ambient temperature (15-25°C) for 3-24 hours depending on scale severity. Monitor pH hourly—pH rising above 4 indicates descaler exhaustion (add further DS40 or replace solution). Inspect heat exchanger surfaces for scale removal.

Critical Hold-Point: CRITICAL: DS40 is highly acidic (pH 1-2, H314 severe burns). Never heat descaler solution (accelerates corrosion and vapour generation). Do not exceed 24-hour contact time on ferrous metals. Ensure mechanical ventilation operational throughout. Emergency eyewash must be within 10m.
5

DS40 Neutralisation, Drain & Multi-Stage Flushing

Descaler Neutralisation & Flushing

Neutralise DS40 in-situ by adding soda ash (sodium carbonate) until pH reaches 6-8 (test with pH strips). Drain neutralised descaler to foul sewer via interceptor tank. Flush system with mains water (minimum 3 system volumes) until discharge pH is stable at 6-8. Inspect drain water for white precipitate (calcium salts) confirming descaling. Check heat exchanger and pipework for corrosion damage. If pH remains <6 after flushing, add further soda ash and re-flush.

Critical Hold-Point: HOLD POINT: Do not add F1 Protector until discharge pH is confirmed 6-8 by two independent tests. Residual acidity will destabilise inhibitor chemistry and cause ongoing corrosion. Dispose of neutralised descaler via licensed waste carrier if trade effluent consent not held.
6

F1 Protector Addition, System Refill & Final Checks

Inhibitor Dosing & Recommissioning

Dose Fernox F1 Protector at 1% system volume (e.g. 10L per 1000L system) via fill point. Refill system with mains water to operational pressure (typically 1.5 bar cold). Vent all high points and radiators to remove air. Pressurise to 2 bar and check for leaks at all joints disturbed during maintenance. Heat system to operating temperature (70-80°C) and circulate for 1 hour. Test inhibitor concentration using Fernox test kit (target: 1-2% v/v). Record batch numbers, dose rates, and test results in site COSHH register. Remove LOTO devices only after system proven leak-free and operational.

Critical Hold-Point: FINAL CHECK: Verify F1 Protector concentration using test strips before releasing system to service. Under-dosing leaves system vulnerable to corrosion. Confirm all drain cocks closed and LOTO tags removed. Update plant logbook with chemical treatment date, products used, and next inspection due (12 months).

Emergency Rescue, First Aid & Spill Protocol

EMERGENCY CONTACTS: National Poisons Information Service 0344 892 0111 | Fernox Technical Support 01799 550811 | Emergency Services 999. FIRST AID: Eye Contact (F3/DS40): Immediately irrigate with eyewash or running water for minimum 15 minutes holding eyelids open. Remove contact lenses if present. Seek immediate medical attention—transport to A&E with SDS. Skin Contact: Remove contaminated clothing. Wash affected area with soap and water for 15 minutes. For DS40 burns, continue irrigation and seek medical attention. Inhalation (DS40 vapours): Move casualty to fresh air immediately. If breathing difficulties persist, administer oxygen if trained and seek medical attention. Ingestion: Do NOT induce vomiting (corrosive risk). Rinse mouth with water. Give small amounts of water to drink. Seek immediate medical attention. SPILLS: Evacuate area and ventilate. Wear full PPE. Contain spill with absorbent pads/granules. Neutralise DS40 spills with soda ash, F3 spills with citric acid. Dispose via licensed waste carrier (EWC 16 03 03*/16 03 04). Report spills >10L to Environment Agency Incident Hotline 0800 807060. FIRE: Products non-flammable but containers may rupture if heated. Use water spray to cool containers. Wear BA if involved in fire (toxic fumes possible).

4. UK HSE Compliance FAQs: Fernox F1 Protector, F3 Cleaner & DS40 Commercial Heating Descaler

Can I mix Fernox F3 Cleaner and DS40 Descaler together to save time on a commercial heating system clean?

Absolutely not—this is extremely dangerous. F3 Cleaner is alkaline (pH 11-13) and DS40 Descaler is acidic (pH 1-2). Mixing them causes a violent exothermic acid-alkali reaction generating heat, pressure surges, and potential system rupture with chemical spray injuries. COSHH Regulations 2002 require you to assess chemical compatibility. You must use F3 first, drain completely, neutralise to pH 6-8, flush thoroughly, then—only if heavy scale remains—use DS40 separately. Always verify pH neutrality between stages using test strips and implement a permit-to-work system for chemical changeovers per BS 7593 segregation requirements.

What PPE do I actually need when dosing Fernox products into a pressurised heating system—our lads are just using rigger gloves?

Rigger gloves are wholly inadequate and non-compliant with COSHH Regulations 2002. For F3 Cleaner (H318 serious eye damage) and DS40 Descaler (H314 severe burns), you must provide and enforce: (1) Chemical-resistant gloves to BS EN ISO 374-1:2016 Type B with 480-minute breakthrough time—nitrile or neoprene, not leather riggers; (2) Safety goggles or full-face shield to BS EN 166:2001 Grade 3 for liquid splash protection; (3) Chemical apron to BS EN 14605:2005 Type 4; (4) S5 safety boots to BS EN ISO 20345:2011. This is not negotiable—DS40 at pH 1-2 causes permanent eye damage in seconds. Install an eyewash station within 10m per BS EN 15154 and train your team in emergency irrigation procedures. Document PPE issue and training in your COSHH assessment.

How do I legally dispose of the dirty water after flushing out Fernox F3 or DS40 from a large commercial system—can it just go down the drain?

It depends on pH and volume, and you risk prosecution under Environmental Protection Act 1990 if you get this wrong. You can discharge to foul sewer (not surface water drains or watercourses) only if: (1) pH is neutralised to 6-9 using soda ash (for DS40) or citric acid (for F3)—verify with calibrated pH test strips; (2) You hold a trade effluent consent from your water authority for commercial volumes (typically >5m³); (3) Discharge passes through an interceptor tank if required by consent conditions. For first flush or heavily contaminated water, collect in a bunded IBC and dispose via a licensed waste carrier under EWC code 16 03 03* (hazardous) or 16 03 04 (non-hazardous). Install spill kits at drain points per PPG6 guidance. Your COSHH assessment must include environmental controls—HSE inspectors will check this. Keep disposal records for 3 years minimum.

5. Operative Toolbox Talk & Competent Person Sign-Off Register

Competent Person & Operative Declaration: By signing below, the Site Supervisor confirms this assessment has been adapted and verified for actual site conditions, and operatives confirm they have attended the pre-start Toolbox Talk for Fernox F1 Protector, F3 Cleaner & DS40 Commercial Heating Descaler and will follow the safe system of work.

Operative / Supervisor Name Trade / Role & CSCS No. Signature Date & Time
1. (Site Supervisor):     
2.     
3.     
4.     
5.     
6.     

Related UK Safety Templates & Risk Assessments