SafeSequence › UK Safety Template Library › Commercial Brand COSHH › Bostik Evo-Stik Impact Contact Adhesive & Gripfill Solvent-Borne Gap Filler
Reference UK COSHH Example • Commercial Brand COSHH

Bostik Evo-Stik Impact Contact Adhesive & Gripfill Solvent-Borne Gap Filler (COSHH Template & 5x5 Risk Assessment)

Under COSHH 2002 Regulation 6, DSEAR 2002 Regulation 6, and EH40/2005 Workplace Exposure Limits, employers must prevent or adequately control exposure to volatile organic compounds (VOCs) in Bostik Evo-Stik Impact Contact Adhesive and Gripfill Solvent-Borne Gap Filler (classified GHS02 flammable, GHS07 harmful, GHS09 environmental hazard). Mandatory engineering controls include local exhaust ventilation (LEV) achieving ≥10 air changes/hour, elimination of ignition sources within ATEX-zoned areas, and respiratory protective equipment (RPE) where 8-hour TWA exceeds 50% WEL. Target residual risk: ≤6 (tolerable) through hierarchy of control implementation, atmospheric monitoring, and health surveillance per HSG258 guidance.

Statutory FrameworkCOSHH 2002, DSEAR 2002, EH40/2005 Volatile Organic Compound (VOC) WELs (GHS02, GHS07, GHS09)
ClassificationGHS02 (Flame - Flammable Liquid Category 2/3), GHS07 (Exclamation Mark - Harmful if inhaled, skin/eye irritation, STOT SE Category 3), GHS09 (Environment - Aquatic toxicity). Contains hydrocarbon solvents (CAS 64742-95-6, 64742-82-1), acetone (CAS 67-64-1). Flash point: Evo-Stik Impact ~-18°C, Gripfill ~32°C. EH40/2005 WELs: Hydrocarbon solvents 1200 mg/m³ 8-hr TWA, Acetone 1210 mg/m³ 8-hr TWA (500 ppm). DSEAR hazardous area classification required where vapour concentration may exceed 10% LEL.
Required Plant / KitLocal Exhaust Ventilation (LEV) system with HEPA filtration and airflow ≥10 air changes/hour (HSG258 compliant, last thorough examination certificate within 14 months) • Intrinsically safe (ATEX-certified) electrical tools and lighting for Zone 1/2 hazardous areas • Calibrated direct-reading VOC monitor (PID or FID) with data-logging capability for real-time atmospheric monitoring • Non-sparking bronze or beryllium-copper hand tools (spatulas, scrapers) for application in flammable atmospheres • Sealed waste containers (UN-approved, metal with flame arrestor) for solvent-contaminated rags and applicators
Site Sign-Off StatusRequires Competent Person Verification
Instant AI Customization or Free Blank Word (.doc) Download

Need this COSHH customized with your Company Name, Site Postcode & Nearest A&E Hospital?

Dictate your site specifics on your phone in 45 seconds to auto-compile a signed PDF—or download our free blank Word (.doc) shell below.

Auto-Fill via Voice / CLP (45s)

1. Mandatory Personal Protective Equipment (BS EN Standards)

BS EN ISO 374-1:2016 Type A (AJKLPT), BS EN 420:2003+A1:2009
Nitrile chemical-resistant gloves (minimum 0.38mm thickness, breakthrough time >480 minutes for hydrocarbon solvents)
Prevent dermal absorption of VOCs and skin sensitisation from prolonged/repeated solvent contact per COSHH ACoP L5 paragraph 127
BS EN 140:1999, BS EN 14387:2004+A1:2008 (Class A2), BS EN 143:2021 (P3)
Half-mask respirator with combined A2P3 filters (organic vapour + particulate) or full-face PAPR where TWA >50% WEL
Control inhalation exposure to VOC vapours below WEL; face-fit testing required every 3 years per HSG53, RPE maintenance log mandatory
BS EN 166:2002 (Optical Class 1, mechanical strength F, liquid droplet/splash 3)
Safety spectacles with side shields or full-face visor for splash protection during dispensing/application
Prevent eye contact with liquid adhesive causing serious irritation (GHS07 H319); emergency eyewash station required within 10m per BS EN 15154
BS EN 13034:2005+A1:2009 (Type 6-PB), BS EN ISO 20345:2011 S3 SRC FO
Chemical-resistant coveralls (Type 6 liquid-tight) and safety footwear with hydrocarbon-resistant soles
Minimise skin contamination and prevent ignition from static discharge; anti-static footwear essential in DSEAR zoned areas

2. 5×5 Hazard Risk Assessment Matrix (HASAWA 1974 / MHSWR 1999)

Identified Hazard & HarmInitial Risk (L×S)Mandatory Engineering, Isolation & Procedural ControlsResidual Risk
1. Inhalation of volatile organic compound (VOC) vapours (hydrocarbons, acetone) in confined/poorly ventilated spaces
Harm: Acute: Dizziness, headache, nausea, respiratory irritation, narcotic effects. Chronic: Central nervous system depression, liver/kidney damage, occupational asthma (COSHH Regulation 7 health surveillance trigger)
4 × 4 = 16Engineering: Install/verify LEV system achieving ≥10 air changes/hour with capture velocity ≥1 m/s at source (HSG258). Administrative: Atmospheric monitoring pre-work and every 2 hours; work permit for confined spaces per L101. RPE: Mandatory A2P3 half-mask (APF 20) or PAPR (APF 40) where monitoring indicates >600 mg/m³ (50% WEL). Rotate operatives every 2 hours to limit exposure duration. Health surveillance: Annual respiratory questionnaire and spirometry per HSG61.2 × 2 = 4
2. Fire/explosion risk from flammable solvent vapours (flash point -18°C to 32°C) in presence of ignition sources
Harm: Catastrophic fire/explosion causing severe burns (full-thickness), blast injuries, structural damage, and multiple fatalities; RIDDOR-reportable dangerous occurrence under Regulation 3(1)
3 × 5 = 15DSEAR Assessment: Classify work area as Zone 2 (vapour cloud possible <10% LEL). Elimination: Remove all ignition sources (hot work, smoking, non-ATEX electrical equipment) within 10m radius. Substitution: Consider water-borne adhesives where technically feasible. Engineering: Bonding/earthing of metal containers (resistance <10Ω); explosion-relief venting. Administrative: Hot work permit system with 60-minute fire watch post-completion. Store <50 litres in DSEAR-compliant flammable cabinet (30-minute fire rating). Emergency: CO₂/foam extinguishers (not water) within 10m; evacuation plan rehearsed quarterly.2 × 3 = 6
3. Skin contact causing irritant contact dermatitis, defatting of skin, and potential sensitisation
Harm: Acute: Erythema, cracking, painful fissures on hands/forearms. Chronic: Occupational dermatitis requiring medical treatment, potential long-term sensitisation preventing future solvent work (COSHH Regulation 11 health record retention 40 years)
5 × 2 = 10Hierarchy: Eliminate hand contact via automated dispensing systems or long-handled applicators. Engineering: Provide touchless soap dispensers and moisturising stations at exit points. PPE: Nitrile gloves (0.38mm, EN 374 Type A) changed every 2 hours or immediately if contaminated; double-gloving for extended tasks. Administrative: Skin surveillance programme (visual inspection monthly); pre-employment baseline skin assessment. Prohibit barrier creams as primary control (COSHH ACoP L5 paragraph 131). Emergency: Wash contaminated skin immediately with soap and water for ≥15 minutes; occupational health referral if dermatitis suspected.3 × 2 = 6
4. Accidental ingestion during hand-to-mouth contact or contaminated food/drink in work area
Harm: Acute gastrointestinal irritation, vomiting, chemical pneumonitis if aspirated into lungs (potentially fatal), systemic toxicity requiring hospital admission
2 × 4 = 8Administrative: Enforce strict hygiene protocol - no eating/drinking/smoking in application areas (signage per Safety Signs Regulations 1996). Designate separate clean mess facility ≥10m from work zone. Mandatory handwashing before breaks (supervised compliance checks). Training: Toolbox talk on aspiration hazard (do NOT induce vomiting if swallowed). Engineering: Provide lockable storage for food/drink outside controlled area. Emergency: If swallowed, rinse mouth and seek immediate medical attention with SDS Section 4; position casualty in recovery position if vomiting to prevent aspiration.1 × 3 = 3
5. Environmental release of VOCs and aquatic-toxic solvents (GHS09) to drains, watercourses, or soil
Harm: Prosecution under Environmental Protection Act 1990 and Environmental Permitting Regulations 2016; aquatic ecosystem damage; contaminated land remediation costs (£10k-£500k+); reputational damage and loss of environmental certification (ISO 14001)
3 × 3 = 9Engineering: Bunded work area with impermeable sheeting and spill containment capacity ≥110% of largest container. Install drain covers/seals before work commences. Provide spill kit (absorbent pads, vermiculite, disposal bags) within 5m. Administrative: Appoint trained spill response operative; emergency contact for Environment Agency (0800 807060) displayed. Waste: Classify as hazardous waste (EWC 08 04 09* - waste adhesives containing dangerous substances); consign via registered carrier with hazardous waste consignment note. Prohibit washing equipment in sinks/drains. Storage: Secondary containment (110% capacity) for bulk containers; weekly integrity inspections logged.1 × 3 = 3

3. Step-by-Step Safe Sequence of Operations & Hold-Points

1

Verify COSHH/DSEAR controls, atmospheric monitoring, and permit-to-work authorisation

Pre-Work Preparation & Hazardous Area Control

Obtain valid permit-to-work signed by competent person (NEBOSH/NVQ Level 6 or equivalent). Verify LEV system operational (manometer reading within green zone, last TExT certificate <14 months old). Conduct baseline atmospheric monitoring using calibrated VOC monitor (zero and span check completed); record readings at breathing zone height. Confirm flammable vapour concentration <10% LEL; if ≥10% LEL, halt work and increase ventilation. Establish DSEAR Zone 2 boundary (10m radius) with warning signs per Safety Signs Regulations 1996. Isolate/lock-off electrical supplies not ATEX-rated; issue LOTO tags to authorised operative only. Confirm emergency equipment in place: CO₂ extinguisher, spill kit, eyewash station, first aider contact details displayed.

Critical Hold-Point: STOP: Do NOT proceed if VOC concentration ≥10% LEL or LEV system inoperative. Flammable atmosphere presents immediate explosion risk. Notify supervisor and await mechanical ventilation/purging. All ignition sources (including mobile phones in non-ATEX cases) must be removed from Zone 2 boundary before opening containers.
2

Don mandatory PPE in correct sequence and verify face-fit integrity

Personal Protective Equipment & Hygiene Baseline

Perform hand hygiene and visual skin inspection (record any pre-existing cuts/dermatitis in daily log). Don chemical-resistant coveralls (Type 6) ensuring cuffs sealed. Fit nitrile gloves (EN 374 Type A, 0.38mm) over coverall sleeves; check for tears/punctures. Don safety footwear (S3 SRC FO anti-static). Conduct negative/positive pressure seal check on A2P3 half-mask respirator per manufacturer instructions (HSG53 protocol); if seal fails, adjust straps or change facepiece size. Don safety spectacles (EN 166 Class 1) ensuring compatibility with respirator. Confirm RPE filter cartridge within use-by date and <6 months since opening (record date opened on cartridge). Designate clean/dirty zones; establish decontamination protocol before breaks.

Critical Hold-Point: MANDATORY HOLD POINT: Supervisor must verify RPE seal check passed before operative enters work area. Failed seal check = immediate exposure to VOCs above WEL. Record seal check outcome on permit-to-work. Facial hair (including stubble >1mm) prevents effective seal - clean-shaven policy enforced per COSHH ACoP L5.
3

Open adhesive containers using non-sparking tools in bunded area with active ventilation

Safe Container Opening & Dispensing

Place container in bunded tray (≥110% capacity) positioned directly beneath LEV hood (capture velocity ≥1 m/s verified with smoke tube test). Bond container to earth point using crocodile clip and verify continuity <10Ω with multimeter. Open lid slowly using non-sparking bronze tool to allow pressure equalisation (vapour release expected). If using Gripfill cartridge gun, pierce seal in well-ventilated area with gun nozzle pointed away from body/face. Decant only the quantity required for immediate use (maximum 500ml) into secondary metal container; reseal primary container immediately. Wipe any spillage on exterior with solvent-resistant cloth and place in sealed metal waste bin. Maintain continuous atmospheric monitoring; if VOC reading exceeds 600 mg/m³ (50% WEL), increase ventilation or reduce work rate.

Critical Hold-Point: EXPLOSION HAZARD: Static discharge during pouring can ignite vapours. Bonding/earthing is NON-NEGOTIABLE. Do not use plastic containers (static accumulation risk). If vapour cloud visible or strong solvent odour detected, evacuate immediately and activate emergency ventilation. Re-entry only after monitoring confirms <10% LEL.
4

Apply adhesive using controlled techniques with continuous ventilation and exposure monitoring

Application & Exposure Control

Apply adhesive in thin, even coats using non-sparking spatula or Gripfill gun at low pressure to minimise aerosol generation. Work in sections ≤2m² to limit open surface area and vapour release. Maintain face position upwind/upstream of LEV airflow; never position head directly over application point. For contact adhesive (Evo-Stik Impact), allow flash-off time (5-15 minutes per manufacturer SDS) before bonding surfaces; during flash-off, vapour release peaks - maintain maximum ventilation. Rotate operatives every 2 hours (record rotation times on permit). Conduct atmospheric monitoring every 30 minutes during application; if TWA trending toward WEL, implement additional controls (increase ventilation, reduce application rate, introduce second LEV unit). Prohibit use of fans that may spread vapours toward ignition sources or unprotected personnel.

Critical Hold-Point: CRITICAL CONTROL: Flash-off period generates highest VOC concentration. All personnel without RPE must evacuate to ≥10m distance. Do NOT accelerate drying with heat guns or other ignition sources - flash point as low as -18°C means vapours will ignite. If operative experiences dizziness, headache, or nausea, evacuate to fresh air immediately and report to first aider (potential acute VOC intoxication).
5

Segregate hazardous waste, decontaminate tools, and conduct post-work atmospheric clearance

Waste Management & Decontamination

Place all contaminated applicators, rags, and PPE in designated metal waste container with self-closing lid (spontaneous combustion risk from solvent-soaked materials). Seal container and label 'Hazardous Waste - EWC 08 04 09* - Flammable VOCs'. Store in external bunded area away from buildings pending collection by licensed carrier (consignment note required). Clean non-disposable tools with minimal solvent in bunded area; allow cleaning rags to dry flat (not bunched) in ventilated area before disposal. Decontaminate work area with damp cloth (not dry sweeping which generates dust/vapour). Conduct final atmospheric monitoring at multiple heights (vapours heavier than air); record readings. Confirm VOC concentration <10% baseline before declaring area safe for unrestricted access. Remove DSEAR boundary signs only after clearance confirmed.

Critical Hold-Point: FIRE RISK: Solvent-soaked rags can spontaneously combust via oxidation if stored in enclosed containers. Metal waste bin must be emptied daily and stored externally. Never leave contaminated materials in plastic bags or enclosed spaces overnight. Multiple fires in UK workplaces attributed to this hazard (HSE investigation reports IN2018/03).
6

Complete exposure records, conduct health checks, and update COSHH assessment

Post-Work Health Surveillance & Documentation

Record total exposure duration, peak VOC readings, and average TWA on COSHH exposure log (retain 40 years per Regulation 11). Operative completes post-shift health questionnaire (symptoms: headache, dizziness, nausea, skin irritation, respiratory issues). Supervisor reviews questionnaire; any positive responses trigger occupational health referral within 48 hours. Inspect operative's hands/forearms for signs of dermatitis; photograph any abnormalities for health record. Clean and store RPE per manufacturer instructions; record filter cartridge usage hours (discard after 40 hours use or 6 months, whichever sooner). Return permit-to-work with all monitoring data and incident/near-miss reports. Update COSHH assessment if any control failures identified; communicate lessons learned in next toolbox talk. Schedule LEV TExT if performance concerns noted.

Critical Hold-Point: LEGAL REQUIREMENT: COSHH Regulation 11 mandates health records retained for 40 years from last exposure. Failure to maintain records = prosecution risk (HSE enforcement notices issued for record-keeping failures). Any suspected occupational disease (dermatitis, asthma, solvent-induced neuropathy) is RIDDOR-reportable under Regulation 8 if results in 7+ days absence or medical treatment.

Emergency Rescue, First Aid & Spill Protocol

**INHALATION (Priority 1):** Remove casualty to fresh air immediately; loosen tight clothing. If breathing is difficult, administer oxygen (if trained and equipment available). If breathing stops, commence CPR and call 999 requesting paramedic attendance (state 'solvent inhalation, possible chemical pneumonitis'). Do NOT leave casualty unattended - VOC intoxication can cause delayed respiratory depression. Monitor consciousness level using AVPU scale. Provide SDS Section 4 to paramedics. Report to HSE under RIDDOR if hospitalisation >24 hours. **SKIN CONTACT:** Remove contaminated clothing immediately (double-bag as hazardous waste). Wash affected area with soap and lukewarm water for minimum 15 minutes (not cold water which closes pores). Do NOT use solvents/thinners to clean skin (increases absorption). Apply emollient cream (not barrier cream). If irritation persists or dermatitis develops, refer to occupational health within 48 hours. Photograph affected area for health record. Launder contaminated clothing separately before reuse. **EYE CONTACT (Priority 1):** Irrigate eyes immediately at emergency eyewash station for minimum 15 minutes, holding eyelids open. Remove contact lenses if present and easy to do. Continue irrigation while arranging urgent medical assessment (ophthalmology referral if corneal damage suspected). Do NOT rub eyes. Provide SDS Section 4 to treating clinician. Eye injuries from solvents are RIDDOR-reportable if result in incapacity for normal work >7 days. **INGESTION (Priority 1):** Do NOT induce vomiting (aspiration into lungs can be fatal). Rinse mouth thoroughly with water (do not swallow). Give small sips of water if conscious and able to swallow. Call 999 immediately and request paramedic attendance stating 'hydrocarbon solvent ingestion, aspiration risk'. Position casualty in recovery position if vomiting to protect airway. Provide SDS and container label to paramedics. Hospital assessment mandatory even if asymptomatic (delayed chemical pneumonitis can develop 6-24 hours post-ingestion). **FIRE/EXPLOSION:** Activate fire alarm and evacuate per emergency plan. Call 999 stating 'flammable solvent fire'. Use CO₂, foam, or dry powder extinguishers only (water will spread fire). If fire involves >5 litres or cannot be controlled within 60 seconds, evacuate and await fire brigade. Treat burns per first aid protocol (cool with running water 20 minutes, cover with cling film, do not burst blisters). All fires involving flammable substances are RIDDOR-reportable as dangerous occurrences under Regulation 3(1). **SPILL >1 LITRE:** Evacuate area and establish 10m exclusion zone. Eliminate ignition sources. Ventilate area. Trained spill response operative (wearing full PPE + RPE) to absorb with vermiculite/sand, never water. Contain with absorbent booms to prevent drain entry. Collect waste in sealed metal container labelled hazardous waste. If spill enters drains/watercourses, immediately notify Environment Agency 24-hour hotline 0800 807060 (legal duty under Environmental Permitting Regulations 2016). Decontaminate area and conduct atmospheric monitoring before re-entry.

4. UK HSE Compliance FAQs: Bostik Evo-Stik Impact Contact Adhesive & Gripfill Solvent-Borne Gap Filler

5. Operative Toolbox Talk & Competent Person Sign-Off Register

Competent Person & Operative Declaration: By signing below, the Site Supervisor confirms this assessment has been adapted and verified for actual site conditions, and operatives confirm they have attended the pre-start Toolbox Talk for Bostik Evo-Stik Impact Contact Adhesive & Gripfill Solvent-Borne Gap Filler and will follow the safe system of work.

Operative / Supervisor Name Trade / Role & CSCS No. Signature Date & Time
1. (Site Supervisor):     
2.     
3.     
4.     
5.     
6.     

Related UK Safety Templates & Risk Assessments