This Standard Operating Procedure (SOP) establishes the mandatory safety requirements for film threading and jam clearing operations on automated rotary arm pallet wrapping machines in accordance with PUWER 1998 (Regulation 11 - Dangerous Parts of Machinery), Manual Handling Operations Regulations 1992, and company Lock Out Tag Out (LOTO) isolation standards. The procedure applies to all maintenance technicians, packaging operators, and engineering personnel who perform film loading, threading, or jam clearance activities on rotary arm stretch wrappers. All work must be conducted under full electrical isolation with stored energy dissipation. The residual risk rating following implementation of engineering controls and safe systems of work is MEDIUM, requiring strict adherence to isolation protocols and permit-to-work procedures. This SOP must be read in conjunction with the manufacturer's maintenance manual and site-specific LOTO procedures.
| Identified Hazard & Harm | Initial Risk (L×S) | Mandatory Engineering, Isolation & Procedural Controls | Residual Risk |
|---|---|---|---|
| 1. Entanglement in rotating rotary arm or film carriage during threading without isolation Harm: Severe crush injuries, traumatic amputation, or fatality from contact with rotating arm (typical speed 30-45 rpm) or pre-stretch rollers (surface speed up to 300m/min) |
4 × 5 = 20 | Mandatory LOTO isolation at main electrical isolator with personal padlock. Verify zero energy state using GS38 voltage tester. Install physical barrier/guard interlock defeat prevention. Implement permit-to-work for all film threading. Ensure emergency stop functionality tested weekly per PUWER Reg 16. | 2 × 5 = 10 |
| 2. Stored energy release from tensioned film or pre-stretch mechanism springs Harm: Lacerations to hands/face from whiplash effect of tensioned film (typical tension 50-150N), eye injuries from spring-loaded components, or impact injuries from sudden mechanism release |
4 × 3 = 12 | Dissipate stored energy by manually releasing film tension using designated release lever before guard removal. Allow 60-second settling period post-isolation. Use controlled film cutting technique working away from body. Maintain minimum 500mm exclusion zone during tension release. Provide spring retention tools per manufacturer specification. | 2 × 3 = 6 |
| 3. Manual handling of film rolls and awkward postures during threading Harm: Musculoskeletal disorders (lower back strain, shoulder injuries) from lifting film rolls (15-25kg) at height or in confined film carriage space, repetitive reaching, and sustained awkward postures |
4 × 2 = 8 | Implement two-person lift for film rolls >15kg or use mechanical film loading trolley/hoist. Position film roll holder at waist height (750-1050mm). Provide adjustable work platform for threading access. Conduct task-specific manual handling training per HSG115 guidance. Rotate tasks to limit exposure to 2 hours continuous threading work. | 2 × 2 = 4 |
| 4. Laceration from sharp film edges and cutting tools during jam clearance Harm: Deep cuts to hands and fingers requiring medical treatment, particularly when clearing jammed film from pre-stretch rollers or cutting tensioned film under load |
5 × 2 = 10 | Mandatory use of BS EN 388 Level C cut-resistant gloves. Provide only retractable safety knives conforming to BS 7951. Prohibit use of Stanley knives or fixed-blade tools. Ensure film is de-tensioned before cutting. Implement 'cut away from body' technique training. Maintain first aid provision within 50m per HSE INDG214. | 2 × 2 = 4 |
| 5. Unexpected machine restart during maintenance due to inadequate isolation or interlock bypass Harm: Catastrophic crush injuries or fatality from sudden rotary arm movement during hands-on work inside the machine guarding envelope |
3 × 5 = 15 | Enforce group LOTO procedure with individual personal padlocks (non-transferable). Isolate at main incoming supply with visible break isolation. Verify isolation using GS38 tester at machine control panel. Display 'DO NOT OPERATE' signage at all control stations. Implement permit-to-work with authorised person sign-off. Conduct pre-start communication sweep before re-energisation per BS 7671 isolation procedures. | 1 × 5 = 5 |
Notify production supervisor and obtain permit-to-work authorisation. Press emergency stop button at operator station. Locate main electrical isolator (typically wall-mounted within 3m of machine). Switch isolator to OFF position and apply personal LOTO padlock through hasp. Affix 'DO NOT OPERATE - MAINTENANCE IN PROGRESS' tag with your name, date, and time. Using calibrated GS38 voltage tester, verify zero voltage at machine control panel terminals L1, L2, L3 and between phases and earth. Record isolation in LOTO logbook. Wait minimum 60 seconds for capacitor discharge and pneumatic pressure bleed-down.
Don all mandatory PPE including cut-resistant gloves and eye protection. Using torque-limiting screwdriver, remove film carriage access guard (typically 4x M6 captive screws). Store guards in designated area away from work zone. Locate film tension release lever on pre-stretch unit (consult machine-specific manual for location). Slowly rotate lever clockwise through 90° to release film tension - maintain 500mm distance and turn face away during release. If film is jammed, use retractable safety knife to cut film at a point between the film roll and first roller, cutting away from your body. Allow all film tension to dissipate before proceeding.
Visually inspect entire film path from roll holder through pre-stretch unit to application point. Identify jam location (common points: pre-stretch roller nip, dancer arm pivot, film carriage guide rails). Using gloved hands, carefully extract jammed film by pulling in direction of normal film travel. For film wrapped around pre-stretch rollers, manually rotate roller in reverse direction while extracting film. Do NOT use excessive force - if film is tightly wound, make multiple small cuts with safety knife to section the jam. Remove all film debris and check for contamination on rollers. Inspect pre-stretch rollers for damage (scoring, rough edges) that may have caused jam. Clean roller surfaces with isopropyl alcohol if adhesive residue present.
Using two-person lift technique or mechanical aid, load new film roll (15-25kg) onto mandrel holder ensuring roll rotates in correct direction (check directional arrow on carriage). Pull film leader (approximately 2m length) from roll. Thread film through dancer arm guide (if fitted) ensuring film passes over tension roller. Feed film into pre-stretch roller nip - use flat hand to guide film, never use fingers to push film between rollers. Continue threading through film carriage guide rails, under clamp bar, and to application point. Leave 300mm tail extending beyond application point. Manually rotate pre-stretch rollers (by hand, machine still isolated) to take up slack and confirm smooth film path with no twists or folds.
Remove all tools, film waste, and foreign objects from machine envelope. Reinstall film carriage access guard ensuring all fasteners are torqued to manufacturer specification (typically 4-6 Nm). Verify all interlock switches are engaged and not defeated. Check emergency stop button is functional (pull-to-test, should remain latched). Conduct visual sweep of entire machine perimeter to ensure no personnel in danger zone. Remove LOTO tag and personal padlock from isolator - only the person who applied the lock may remove it. Return isolator to ON position. Reset emergency stop by twisting clockwise. Inform production supervisor that maintenance is complete and machine is ready for controlled restart.
With all personnel clear of machine envelope, select 'Manual' or 'Jog' mode on control panel. Initiate single-cycle test wrap at reduced speed (typically 50% normal speed). Observe film application for correct tension, overlap, and placement. Monitor for unusual noises, vibrations, or film tracking issues. If test successful, run second cycle at normal operating speed. Verify film consumption rate is within normal parameters. Complete maintenance logbook entry recording: date, time, nature of jam, corrective action taken, test results, and your signature. Brief production operator on any observations or precautions. Hand over machine to production with confirmation that all safety systems are functional.
In the event of entanglement or entrapment, immediately activate the nearest emergency stop button (red mushroom head, located at operator station and maintenance access points). If emergency stop is inaccessible, isolate power at main electrical isolator. DO NOT attempt to pull trapped person free while machine is energised. Summon immediate assistance and call emergency services (999) for serious injuries. For entanglement injuries, only trained rescue personnel should attempt extraction to avoid exacerbating crush injuries. For lacerations from film edges or cutting tools, apply direct pressure with sterile dressing and elevate injured limb. All injuries must be reported immediately to site management and recorded in the accident book (RIDDOR notification required for injuries resulting in 7+ days absence or specified injuries including amputations). First aid provision must be available within 50m of packaging operations per HSE guidance INDG214. Ensure appointed first aiders hold valid HSE-approved certificates (FAW or EFAW). In case of suspected musculoskeletal injury from manual handling, do not continue work - report to supervisor and seek occupational health assessment. Emergency contact numbers must be displayed at machine location including: Site First Aider, Maintenance Supervisor, and Emergency Services.
No. PUWER 1998 Regulation 11 requires that access to dangerous parts of machinery must be prevented, or where access is necessary, the machinery must be stopped before access is gained. Film threading and jam clearance require hands-on contact within the guarding envelope where rotating parts (rotary arm, pre-stretch rollers) present entanglement hazards. 'Inching' or 'jog' modes do not constitute adequate safeguarding as unexpected movement can still occur due to control system faults, operator error, or stored energy release. Full electrical isolation with LOTO is the only acceptable method. HSE guidance HSG274 'Safeguarding of Machinery' confirms that maintenance and setting activities requiring guard removal must be conducted under isolation unless specifically designed safe maintenance features (e.g., trapped key interlocks with hold-to-run controls at reduced speed <10mm/s) are engineered into the machine per BS EN ISO 14120:2015. Standard rotary arm wrappers do not typically incorporate such features for film threading, therefore isolation is mandatory.
No. The fundamental principle of Lock Out Tag Out procedures, supported by HSE guidance and BS 7671:2018 isolation procedures, is that only the person who applied a personal lock may remove it. This ensures the individual who is exposed to the hazard maintains sole control over their own safety. Master keys or supervisor override capabilities fundamentally undermine the LOTO system and are not permitted under competent UK safety management systems. In genuine emergencies where a worker is incapacitated and their lock must be removed (e.g., medical emergency, worker has left site), a formal emergency lock removal procedure must be followed involving: senior management authorisation, thorough verification that the worker is not in the hazard zone, documented justification, and investigation of why the emergency arose. The HSE's view, expressed in enforcement notices, is that routine use of master keys or supervisor override constitutes a failure to adequately control risks under PUWER Regulation 11 and Section 2 of the Health and Safety at Work Act 1974. Each authorised person must have their own uniquely keyed padlock.
PUWER Regulation 16 requires that equipment is maintained in efficient working order and good repair, with maintenance logs kept. For safety-critical control systems including emergency stops, HSE guidance (HSG274 and supporting standards BS EN ISO 13850:2015 for emergency stop function) recommends functional testing at intervals determined by risk assessment and manufacturer recommendations. Industry best practice for packaging machinery emergency stops is weekly functional testing (pull-to-test, verify machine stops and power is interrupted, reset function operates correctly) documented in a maintenance log, plus formal inspection and electrical continuity testing as part of annual thorough examination. The test frequency should be increased if: the machine operates in harsh environments (dust, moisture), emergency stops are frequently activated (indicating potential wear), or incident/near-miss history suggests reliability issues. Pre-use checks by operators should include visual inspection of emergency stop buttons for damage or obstruction. Any emergency stop that fails testing must result in machine withdrawal from service until repaired and re-tested. Regulation 16 also requires that maintenance activities themselves (including emergency stop testing) are conducted safely - testing should be performed under controlled conditions with appropriate isolation for electrical testing components.
Competent Person & Operative Declaration: By signing below, the Site Supervisor confirms this assessment has been adapted and verified for actual site conditions, and operatives confirm they have attended the pre-start Toolbox Talk for Automated Rotary Arm Pallet Wrapper Film Threading & Jam Clearing and will follow the safe system of work.
| Operative / Supervisor Name | Trade / Role & CSCS No. | Signature | Date & Time |
|---|---|---|---|
| 1. (Site Supervisor): | |||
| 2. | |||
| 3. | |||
| 4. | |||
| 5. | |||
| 6. |