SafeSequence › UK Safety Template Library › Manufacturing & Production › High-Speed Packaging Conveyor Jam Recovery & LOTO Verification
Verified UK SOP Standard • Manufacturing & Production

High-Speed Packaging Conveyor Jam Recovery & LOTO Verification (SOP Template & 5x5 Risk Assessment)

This Standard Operating Procedure (SOP) provides comprehensive guidance for safely recovering jams on high-speed packaging conveyors in compliance with PUWER 1998, BS EN ISO 14119 (Interlocking Devices), and HASAWA 1974. The procedure mandates Lock-Out Tag-Out (LOTO) verification protocols to eliminate hazardous energy sources before personnel intervention. All operatives must be trained in isolation procedures, understand interlocking device functionality, and verify zero-energy states. This SOP applies to all packaging line conveyors operating above 30 metres per minute and requires competent person supervision for complex jam scenarios. Risk assessments identify crushing, entanglement, and electrical hazards with engineering controls and administrative safeguards to reduce residual risk to tolerable levels.

Statutory FrameworkPUWER 1998, BS EN ISO 14119 Interlocking Devices, HASAWA 1974
ClassificationNot Applicable – This SOP addresses mechanical and electrical hazards associated with conveyor systems. No hazardous substances under CLP Regulation (EC) 1272/2008 are involved in jam recovery operations. However, cleaning agents used during maintenance must have separate COSHH assessments.
Required Plant / KitPersonal LOTO padlock and tag set (unique identification) • Calibrated voltage detector/proving unit (GS38 compliant) • Non-conductive hook tool for debris removal (insulated to 1000V) • Torque-limiting screwdriver set for guard removal (2-10 Nm range) • Portable LED task lighting (110V or battery-operated, IP65 rated)
Review Cycle12 Months / Post-Incident
Instant AI Customization or Free Blank Word (.doc) Download

Need this SOP customized with your Company Name, Site Postcode & Nearest A&E Hospital?

Dictate your site specifics on your phone in 45 seconds to auto-compile a signed PDF—or download our free blank Word (.doc) shell below.

Auto-Fill via Voice / CLP (45s)

2. 5×5 Hazard Risk Assessment Matrix (HASAWA 1974 / MHSWR 1999)

Identified Hazard & Harm Initial Risk (L×S) Mandatory Engineering, Isolation & Procedural Controls Residual Risk
1. Entanglement in moving conveyor belts, rollers, or drive chains
Harm: Severe crush injuries, traumatic amputation, or fatality from being drawn into nip points or rotating machinery
4 × 5 = 20 Mandatory LOTO isolation of all energy sources (electrical, pneumatic, hydraulic). Verify zero-energy state using calibrated test equipment. Implement group lockout for multi-person tasks. Install BS EN ISO 14119 compliant interlocks on all access guards. Prohibit bypass of safety devices without permit-to-work. 2 × 4 = 8
2. Electrical shock from exposed live conductors or faulty motor circuits
Harm: Electrocution, cardiac arrest, severe burns, or secondary injuries from falls following electric shock
3 × 5 = 15 Isolate electrical supply at main isolator and apply personal LOTO padlock. Use GS38-compliant voltage detector to prove dead before work commences. Maintain minimum approach distances to HV equipment (>1m). Ensure all electrical work by competent persons only. Implement permit-to-work for complex electrical isolation. 1 × 5 = 5
3. Stored energy release from pneumatic systems or tensioned belts
Harm: Impact injuries from sudden movement of conveyor components, compressed air injection injuries, or whiplash from belt release
4 × 4 = 16 Isolate and depressurize all pneumatic lines. Bleed residual pressure via controlled venting. Use mechanical restraints or blocking devices to prevent unexpected movement. Verify belt tension release before guard removal. Display warning signage at isolation points. Implement double-check verification by second competent person. 2 × 3 = 6
4. Manual handling of jammed packages or heavy conveyor components
Harm: Musculoskeletal disorders, acute back strain, herniated discs, or crush injuries from dropped loads
5 × 3 = 15 Conduct task-specific manual handling risk assessment per HSE guidance. Use mechanical aids (hoists, trolleys) for loads >25kg. Implement team lifting protocols with clear communication. Train operatives in correct lifting techniques. Remove packages systematically to reduce load. Provide adjustable work platforms to optimize posture. 3 × 2 = 6
5. Slips, trips, and falls on packaging debris or elevated conveyor platforms
Harm: Fractures, head injuries, lacerations, or falls from height (>2m) resulting in major injury or fatality
4 × 3 = 12 Maintain clear egress routes and remove debris immediately. Provide slip-resistant flooring (R10 rating minimum). Install guardrails and toe boards on elevated platforms per Work at Height Regulations 2005. Use mobile access equipment (MEWP) for high-level access. Ensure adequate lighting (minimum 500 lux). Implement 5S housekeeping protocols. 2 × 2 = 4

3. Step-by-Step Safe Sequence of Operations & Hold-Points

1

Conduct pre-task briefing and dynamic risk assessment

Preparation & Risk Assessment

Assemble the authorized jam recovery team (minimum 2 persons). Review the specific jam location, type of material involved, and conveyor configuration. Complete a dynamic risk assessment using the site-specific form. Identify all energy sources (electrical, pneumatic, hydraulic, gravitational). Confirm all team members are trained in LOTO procedures and understand the isolation sequence. Establish communication protocols and emergency signals. Notify production supervisor and adjacent line operators of impending shutdown.

Critical Hold-Point: HOLD POINT: Do NOT proceed until dynamic risk assessment is signed off by a competent person and all team members confirm understanding of hazards and controls.
2

Execute full electrical and pneumatic isolation with personal LOTO

Isolation & LOTO Application

Locate the conveyor's main electrical isolator (refer to isolation schedule posted at control panel). Switch isolator to OFF position and apply personal LOTO padlock and tag with name, date, and time. If multiple energy sources exist, apply group lockout hasp. Isolate pneumatic supply at the dedicated shut-off valve and bleed residual pressure via manual vent. Apply secondary LOTO to pneumatic isolation valve. For hydraulic systems, isolate pump and release pressure per manufacturer's instructions. Record all isolation points on the LOTO permit.

Critical Hold-Point: HOLD POINT: Verify each team member has applied their personal LOTO device. Do NOT proceed until all energy sources are isolated and tagged. Attempting to clear jams on live equipment is STRICTLY PROHIBITED and may result in disciplinary action.
3

Verify zero-energy state using calibrated test equipment

Verification & Proving Dead

Using a GS38-compliant voltage detector, test the device on a known live source to prove functionality. Test all accessible electrical terminals and motor connections within the jam area to confirm dead. Attempt to restart the conveyor using the control panel start button (it must NOT operate). Physically inspect for any residual movement of belts or rollers. Check pneumatic pressure gauges read zero. For belt-driven systems, manually rotate the drive pulley to confirm no unexpected resistance or stored energy. Document verification results on the LOTO permit.

Critical Hold-Point: HOLD POINT: Do NOT open guards or access jam area until zero-energy state is independently verified by a second competent person. Re-test voltage detector on known live source after proving dead to confirm continued functionality.
4

Remove interlocked guards using correct procedures and tools

Guard Removal & Access

Identify all guards requiring removal to access the jam (refer to conveyor layout drawing). Check that interlocking devices (BS EN ISO 14119) are properly disengaged and will not re-energize the system. Use torque-limiting screwdrivers to remove guard fasteners to prevent damage to threads. Place removed guards in a designated safe area away from the work zone. Position portable LED task lighting to illuminate the jam area adequately (minimum 500 lux). Establish a physical barrier or warning signage to prevent unauthorized access to the open conveyor section.

Critical Hold-Point: WARNING: Never bypass, override, or defeat interlocking devices. Any defective interlocks must be reported immediately and the conveyor taken out of service until repaired by a competent maintenance engineer.
5

Systematically remove jammed materials using safe techniques

Jam Clearance

Wearing all mandatory PPE, visually assess the jam configuration and identify the safest removal sequence. Use non-conductive hook tools to extract packaging materials from nip points—never use hands directly. For heavy or wedged packages, use mechanical aids (hoists, pry bars) and team lifting techniques. Remove materials in reverse order of jamming where possible. Inspect conveyor belt, rollers, and drive chains for damage, foreign objects, or wear. Check for root causes (misaligned guides, damaged sensors, incorrect package orientation). Clear all debris from the conveyor bed and surrounding area. Place removed materials in designated waste or rework containers.

Critical Hold-Point: WARNING: Do NOT reach into nip points or confined spaces without confirming zero-energy state. If jam cannot be safely cleared, STOP work and escalate to maintenance engineering for disassembly.
6

Reinstall guards, remove LOTO, and conduct pre-start verification

Restoration & Verification

Reinstall all guards in reverse order of removal, ensuring correct alignment and fastener torque. Verify interlocking devices engage correctly and are not damaged. Conduct a final visual inspection to confirm no tools, materials, or personnel remain in the hazard zone. Remove all personal LOTO devices only after confirming all team members are clear and accounted for. Restore pneumatic and electrical supplies in correct sequence. Conduct a controlled restart: first jog the conveyor in inch mode to verify correct operation, then run at reduced speed for 30 seconds observing for abnormal noise or vibration. Return to normal production speed only after confirming safe operation. Complete LOTO permit and file in the site logbook.

Critical Hold-Point: HOLD POINT: Conduct a final head count and confirm all personnel are clear before removing LOTO devices. Do NOT remove another person's LOTO device under any circumstances. Verify all guards are correctly reinstalled and interlocks functional before re-energizing.

Emergency Rescue, First Aid & Spill Protocol

In the event of injury during jam recovery operations, immediately activate the emergency stop (E-stop) button if the conveyor is energized. Call for the site first aider and dial 999 for serious injuries (crush injuries, electrocution, falls from height). Do NOT attempt to move casualties with suspected spinal injuries. For electrical shock, ensure the power source is isolated before approaching the casualty. Administer CPR if trained and the casualty is not breathing. For crush injuries, control bleeding with direct pressure and elevate the injured limb if possible. All injuries, including near-misses, must be reported to the site HSE manager and recorded in the accident book per RIDDOR 2013 requirements. Preserve the scene for investigation and do NOT restart the conveyor until cleared by HSE management. Emergency contact numbers and first aid stations are posted at each production line control panel.

4. UK HSE Compliance FAQs: High-Speed Packaging Conveyor Jam Recovery & LOTO Verification

What is the legal requirement for LOTO under PUWER 1998, and can I use a single master lock for multiple conveyors?

PUWER 1998 Regulation 19 requires that machinery is isolated from all energy sources and measures are taken to prevent re-energization during maintenance or cleaning. While the regulation does not explicitly mandate LOTO, it is recognized UK HSE best practice for achieving compliance. Each person working in the hazard zone must apply their own personal LOTO device—using a single master lock for multiple conveyors or multiple workers is NOT acceptable as it does not provide individual protection. Group lockout hasps should be used when multiple workers are involved, allowing each person to apply their own padlock. The last person to leave the work area removes their lock last, ensuring no one is exposed to unexpected energization.

How do I verify that interlocking devices comply with BS EN ISO 14119, and what should I do if I find a defeated interlock?

BS EN ISO 14119 specifies requirements for interlocking devices associated with guards, including coding (mechanical, magnetic, electronic) and tamper resistance. Verification involves checking that guards cannot be opened without stopping the machine, interlocks are not easily defeated (e.g., using magnets or tools), and they are regularly inspected per the manufacturer's schedule (typically 6-monthly). If you discover a defeated, bypassed, or non-functional interlock, you must immediately take the conveyor out of service, apply LOTO, and report it to your supervisor and maintenance engineering. Operating machinery with defeated safety devices is a criminal offense under HASAWA Section 7 (duty of employees) and PUWER Regulation 11 (dangerous parts of machinery). The interlock must be repaired or replaced by a competent person before the conveyor is returned to service.

What is the difference between 'isolation' and 'switching off', and why can't I just use the emergency stop button to clear a jam?

Switching off (including using the emergency stop button) de-energizes the machine but does NOT prevent accidental or unauthorized re-energization. Isolation involves physically disconnecting the energy source (e.g., opening and locking an isolator switch) and applying LOTO to prevent anyone from re-energizing the equipment while work is in progress. Emergency stop buttons are NOT isolation devices—they can be reset by anyone, and electrical faults or control system malfunctions can cause unexpected restarts. UK HSE guidance (HSG 274) and PUWER 1998 Regulation 19 require isolation for any work involving access to dangerous parts of machinery. Using only the E-stop to clear jams exposes you to life-threatening entanglement and crush hazards. Always follow the full LOTO procedure as detailed in this SOP.

5. Operative Toolbox Talk & Competent Person Sign-Off Register

Competent Person & Operative Declaration: By signing below, the Site Supervisor confirms this assessment has been adapted and verified for actual site conditions, and operatives confirm they have attended the pre-start Toolbox Talk for High-Speed Packaging Conveyor Jam Recovery & LOTO Verification and will follow the safe system of work.

Operative / Supervisor Name Trade / Role & CSCS No. Signature Date & Time
1. (Site Supervisor):     
2.     
3.     
4.     
5.     
6.     

Related UK Safety Templates & Risk Assessments