SafeSequence › UK Safety Template Library › Warehousing & MHE › Counterbalance & Reach Truck Pre-Shift PUWER / LOLER Inspection
Verified UK SOP Standard • Warehousing & MHE

Counterbalance & Reach Truck Pre-Shift PUWER / LOLER Inspection (SOP Template & 5x5 Risk Assessment)

This Standard Operating Procedure (SOP) establishes the mandatory pre-shift inspection protocol for counterbalance and reach forklift trucks in compliance with the Provision and Use of Work Equipment Regulations 1998 (PUWER) and Lifting Operations and Lifting Equipment Regulations 1998 (LOLER). The procedure ensures that all rider-operated lift trucks are examined for defects, mechanical integrity, and safe working condition before operational use, in accordance with HSE guidance document L117. All operators must be trained and authorised under the Approved Code of Practice (ACOP) and hold valid certification. This inspection regime forms part of the employer's duty to maintain work equipment and prevent foreseeable risks. Defects identified must be reported immediately, and equipment withdrawn from service until rectified by a competent person. Records must be retained for audit and regulatory inspection purposes.

Statutory FrameworkPUWER 1998, LOLER 1998, HSE Rider-Operated Lift Trucks (L117)
ClassificationNot applicable - This procedure covers mechanical handling equipment inspection. However, operators must be aware of any hazardous substances being transported (refer to site COSHH assessments and Safety Data Sheets). If transporting goods classified under UN/ADR or CLP Regulation (EC) No 1272/2008, ensure compatibility with load handling attachments and observe segregation requirements.
Required Plant / KitCounterbalance or reach forklift truck (subject to inspection) • Pre-shift inspection checklist (PUWER/LOLER compliant) • Defect reporting tags (red 'DO NOT USE' labels) • Tyre pressure gauge (for pneumatic tyres) • Torch or inspection lamp (for undercarriage and hydraulic inspection)
Review Cycle12 Months / Post-Incident
Instant AI Customization or Free Blank Word (.doc) Download

Need this SOP customized with your Company Name, Site Postcode & Nearest A&E Hospital?

Dictate your site specifics on your phone in 45 seconds to auto-compile a signed PDF—or download our free blank Word (.doc) shell below.

Auto-Fill via Voice / CLP (45s)

2. 5×5 Hazard Risk Assessment Matrix (HASAWA 1974 / MHSWR 1999)

Identified Hazard & Harm Initial Risk (L×S) Mandatory Engineering, Isolation & Procedural Controls Residual Risk
1. Undetected mechanical failure (brakes, steering, hydraulics) leading to loss of control
Harm: Collision with pedestrians, racking, or structures causing multiple fatalities or serious crush injuries
4 × 5 = 20 Mandatory pre-shift inspection per PUWER Reg 5 & 6; documented checklist covering brakes, steering, hydraulics, tyres, and warning devices; immediate withdrawal from service if defects identified; competent person repair only; six-monthly thorough examination per LOLER Reg 9; operator training to RTITB/AITT standard; segregated pedestrian routes. 2 × 4 = 8
2. Hydraulic system failure or hose rupture during lifting operations
Harm: Uncontrolled descent of load causing crushing injuries or fatalities; hydraulic injection injuries
3 × 5 = 15 Visual inspection of all hydraulic hoses, rams, and connections for leaks, wear, or damage; check mast chains for wear and lubrication; test lift/tilt/side-shift functions under no-load; pressure relief valve testing during thorough examination; never place body parts under raised loads; LOLER-compliant maintenance schedule; use of manufacturer-approved hydraulic fluid only. 2 × 4 = 8
3. Defective braking system (service or parking brake)
Harm: Runaway truck on inclines causing collision, crushing, or entrapment injuries; potential multiple casualties
3 × 5 = 15 Test service brake effectiveness at low speed in safe area; test parking brake on level ground with load applied; check brake fluid levels (where applicable); inspect brake linkages and cables for wear; immediate isolation if brake response inadequate; speed limits enforced in warehouse; gradient risk assessments for ramps; wheel chocks available for emergency use. 1 × 4 = 4
4. Electrical hazards from damaged battery compartment, wiring, or charging equipment
Harm: Electric shock, burns, or electrocution; risk of fire or explosion from battery gases (hydrogen)
2 × 4 = 8 Visual inspection of battery compartment for damage, corrosion, or loose connections; check for exposed wiring or damaged insulation; ensure battery restraints secure; ventilation adequate in charging areas; no smoking/naked flames near batteries; battery charging only by trained personnel; isolation procedures (LOTO) for maintenance; portable appliance testing (PAT) for chargers. 1 × 3 = 3
5. Operator error due to unfamiliarity with specific truck model or defects not reported
Harm: Loss of control, tip-over, or collision causing serious injury or death; load drop incidents
3 × 4 = 12 Operator competency verification before use (valid in-house authorisation); familiarisation training for different truck types (counterbalance vs reach); clear defect reporting procedure with 'DO NOT USE' tagging system; supervisor sign-off on inspection checklists; near-miss reporting culture; refresher training every 3-5 years per HSE L117 guidance; daily toolbox talks on emerging hazards. 2 × 3 = 6

3. Step-by-Step Safe Sequence of Operations & Hold-Points

1

Verify Operator Authorisation and Obtain Inspection Checklist

Preparation

Confirm you hold valid in-house authorisation for the specific truck type (counterbalance or reach). Obtain the pre-shift inspection checklist from the supervisor or designated location. Verify the truck identification number matches the checklist. Ensure you are wearing all mandatory PPE (safety footwear, hi-vis, gloves). Check the truck is parked on level ground with forks lowered, mast vertical, and parking brake applied.

Critical Hold-Point: STOP: Do not proceed if you are not trained and authorised for this specific truck type. Operating without valid certification is a breach of PUWER Regulation 9 and may result in disciplinary action and prosecution.
2

Conduct Walk-Around Visual Inspection of Truck Condition

Visual Inspection (Exterior)

Perform a 360-degree walk-around inspection. Check for visible damage to bodywork, overhead guard, and counterweight. Inspect tyres for cuts, wear, correct inflation (pneumatic), or damage (solid). Examine forks for cracks, bends, or wear (heel thickness must meet manufacturer specification). Check fork locking pins are secure. Inspect mast channels and chains for wear, damage, or inadequate lubrication. Look for hydraulic fluid leaks under the truck and around rams/hoses. Verify all lights, beacons, and reversing alarms are intact.

Critical Hold-Point: HOLD POINT: If any structural damage, fork cracks, or significant hydraulic leaks are observed, attach a 'DO NOT USE' tag immediately and report to supervisor. Do not attempt to operate the truck.
3

Inspect Operator Controls, Seat, and Safety Devices

Operator Station Checks

Mount the truck using three points of contact. Check the operator seat is secure, adjustable, and seatbelt (if fitted) is functional. Inspect the condition of all control levers, steering wheel, and pedals for damage or excessive wear. Verify the hour meter reading and record on checklist. Check the fire extinguisher is present, in-date, and gauge shows correct pressure. Ensure the operator manual is available in the cab. Test the horn and all warning devices.

Critical Hold-Point: CRITICAL: If seatbelt is fitted and defective, or if horn/reversing alarm is non-functional, the truck must not be used. These are legal requirements under PUWER and site traffic management rules.
4

Test All Controls and Safety Systems Before Movement

Functional Testing (Static)

With the parking brake applied and truck stationary, start the engine or power up (electric). Check all gauges (fuel, battery charge, hydraulic temperature, warning lights). Test the service brake pedal for correct resistance and response. Test the parking brake by attempting to move with brake engaged (should not move). Operate the lift, tilt, and side-shift (if fitted) controls through full range of motion with no load—observe for smooth operation, unusual noises, or jerky movement. Check for hydraulic leaks during operation. Test the steering for smooth response and no excessive play.

Critical Hold-Point: HOLD POINT: If brakes do not respond correctly, hydraulics are jerky or leaking, or steering has excessive play, shut down immediately and report. Do not proceed to dynamic testing.
5

Conduct Low-Speed Operational Test in Designated Safe Area

Functional Testing (Dynamic)

In a clear, designated area away from pedestrians and obstructions, drive the truck forward and reverse at low speed. Test the service brake effectiveness by performing controlled stops. Test steering response in both directions. Raise and lower the forks to maximum height (unloaded) and observe mast operation for smooth movement and no unusual noises. Check visibility in all directions including mirrors (if fitted). Test the reach mechanism (reach trucks only) for smooth extension and retraction. Return to parking position and lower forks fully.

Critical Hold-Point: SAFETY CRITICAL: Never raise forks to full height in areas with overhead obstructions, services, or sprinkler systems. Maintain awareness of pedestrians and other MHE during testing. If any abnormality is detected, cease operation immediately.
6

Complete Inspection Checklist and Report Defects

Documentation and Handover

Return to parking area and shut down the truck correctly. Complete all sections of the pre-shift inspection checklist, recording any defects or observations. If defects are identified, attach a 'DO NOT USE' tag to the steering wheel and inform the supervisor immediately. If the truck passes inspection, sign and date the checklist and file in the designated location. Record the truck as available for operational use in the shift log. Ensure the keys are secured or handed to the next authorised operator with a verbal handover of truck condition.

Critical Hold-Point: LEGAL REQUIREMENT: Inspection records must be retained for minimum 2 years for PUWER compliance and available for HSE inspection. Failure to report known defects may result in personal liability under Section 7 of the Health and Safety at Work Act 1974.

Emergency Rescue, First Aid & Spill Protocol

In the event of an incident during pre-shift inspection: (1) STOP all operations immediately and secure the area. (2) If injury occurs, call for a First Aider and dial emergency services (999) if serious. (3) If hydraulic injection injury is suspected (high-pressure fluid entering skin), treat as a medical emergency requiring immediate hospital treatment—do not delay. (4) If fire occurs, use the truck-mounted CO2 extinguisher (electrical fires) or evacuate and call Fire Brigade. (5) If the truck becomes unstable or tips, do not attempt to right it—cordon off the area and call for specialist recovery. (6) Report all incidents, near-misses, and dangerous occurrences to your supervisor and complete an accident report form. (7) Preserve the scene for investigation and do not move the truck unless it presents an immediate danger. (8) For battery acid exposure, irrigate affected area with water for 15 minutes and seek medical attention. First Aid facilities and trained First Aiders are located [insert site-specific location]. Emergency contact numbers must be displayed in the warehouse office and on notice boards.

4. UK HSE Compliance FAQs: Counterbalance & Reach Truck Pre-Shift PUWER / LOLER Inspection

What is the legal difference between PUWER and LOLER inspections, and how often must forklift trucks be examined?

PUWER 1998 requires that all work equipment is maintained in safe working order through regular inspection and maintenance (Regulations 5 & 6). This includes daily pre-shift checks by operators. LOLER 1998 specifically applies to lifting equipment and requires a 'thorough examination' by a competent person—for forklift trucks, this is typically every 6 months if used for lifting (Regulation 9). LOLER examinations must be documented with a written report. Pre-shift inspections under PUWER are operator-level checks; LOLER examinations are in-depth technical inspections. Both are legal requirements and failure to comply can result in prosecution and Improvement/Prohibition Notices from HSE.

If I identify a defect during the pre-shift inspection, am I allowed to continue using the truck if the defect seems minor?

No. Under PUWER Regulation 5, equipment must not be used if it is not safe. Even 'minor' defects can escalate into serious failures. You must report all defects immediately to your supervisor, attach a 'DO NOT USE' tag, and withdraw the truck from service. Only a competent person (qualified engineer or technician) can assess the defect and authorise return to service after repair. Using defective equipment exposes you to personal liability under Section 7 of the Health and Safety at Work Act 1974 and could result in disciplinary action. The HSE L117 guidance is clear: 'If in doubt, take it out of service.'

Do I need to repeat the pre-shift inspection if I use the same truck after a break or if someone else has already inspected it today?

Yes, if you are taking control of the truck at the start of your shift or after a significant break. Each operator is responsible for satisfying themselves that the equipment is safe before use (PUWER Regulation 5). While a truck may have been inspected earlier in the day, conditions can change—damage may have occurred during previous use, or defects may have developed. Best practice is to conduct a brief visual and functional check even if a full inspection was completed earlier. This is particularly important in multi-shift operations. Your signature on the checklist confirms you have personally verified the truck's condition and are accepting responsibility for its safe operation during your shift.

5. Operative Toolbox Talk & Competent Person Sign-Off Register

Competent Person & Operative Declaration: By signing below, the Site Supervisor confirms this assessment has been adapted and verified for actual site conditions, and operatives confirm they have attended the pre-start Toolbox Talk for Counterbalance & Reach Truck Pre-Shift PUWER / LOLER Inspection and will follow the safe system of work.

Operative / Supervisor Name Trade / Role & CSCS No. Signature Date & Time
1. (Site Supervisor):     
2.     
3.     
4.     
5.     
6.     

Related UK Safety Templates & Risk Assessments