This Standard Operating Procedure (SOP) establishes the mandatory safe system of work for charging traction batteries and topping-up with distilled water in warehousing and materials handling equipment (MHE) operations. The procedure addresses significant hazards including sulphuric acid exposure, hydrogen gas evolution during charging, electrical risks, and manual handling. It is designed to ensure full compliance with the Provision and Use of Work Equipment Regulations 1998 (PUWER), Control of Substances Hazardous to Health Regulations 2002 (COSHH), Dangerous Substances and Explosive Atmospheres Regulations 2002 (DSEAR), and follows guidance in HSG136 (Workplace Transport Safety). All personnel involved in battery charging and maintenance must be trained and competent in this procedure before commencing work. The battery charging area must be designated, well-ventilated, and equipped with appropriate emergency facilities.
| Identified Hazard & Harm | Initial Risk (L×S) | Mandatory Engineering, Isolation & Procedural Controls | Residual Risk |
|---|---|---|---|
| 1. Sulphuric acid exposure (skin/eye contact, inhalation of mist) Harm: Severe chemical burns, permanent eye damage, respiratory tract irritation, dermatitis |
4 × 5 = 20 | Mandatory PPE (BS EN 166 goggles, BS EN ISO 374 gloves, chemical apron). Use closed topping-up systems with anti-spill valves. Emergency eyewash station within 10m (BS EN 15154). COSHH assessment reviewed annually. Neutralising agent (sodium bicarbonate) available. Spill kit maintained. Competency-based training with refresher every 12 months. | 2 × 4 = 8 |
| 2. Hydrogen gas accumulation creating explosive atmosphere during charging Harm: Fire, explosion, severe burns, fatalities, structural damage |
3 × 5 = 15 | Designated battery charging area with mechanical ventilation (minimum 5 air changes/hour per DSEAR). Ventilation interlock on charging equipment - charging disabled if ventilation fails. Portable hydrogen detector with LEL alarm. No ignition sources within 2m (no smoking, naked flames, spark-producing tools). Chargers with automatic shut-off. Batteries allowed to cool before topping-up. DSEAR risk assessment and zoning (Zone 2 classification). Intrinsically safe equipment only. | 1 × 5 = 5 |
| 3. Electrical shock from charging equipment or battery terminals Harm: Electrocution, cardiac arrest, severe burns, secondary injuries from falls |
3 × 5 = 15 | All charging equipment PAT tested and inspected per PUWER (6-monthly). RCD protection (30mA) on all circuits. Insulated tools used. Battery terminals covered when not connected. LOTO procedure applied during maintenance. Competent person (electrically qualified) to inspect equipment. Dry working environment maintained. No charging with damaged cables/connectors - tag and quarantine. Permit-to-work for any electrical maintenance. | 1 × 5 = 5 |
| 4. Manual handling of heavy batteries and distilled water containers Harm: Musculoskeletal disorders, back injury, crush injuries to hands/feet, hernias |
4 × 3 = 12 | Mechanical handling aids provided (battery lifting beams, trolleys, hoists). Manual handling assessment per HSE guidance. Team lifts for batteries >25kg (two-person minimum). Ergonomic design of charging stations (waist height). Distilled water supplied in manageable containers (<10L) or via fixed dispensing system. Training in safe lifting techniques. Task rotation to reduce repetitive strain. Clear access routes maintained. | 2 × 2 = 4 |
| 5. Slips, trips and falls in battery charging area (wet surfaces, trailing cables) Harm: Fractures, head injuries, lacerations, secondary acid contact injuries |
4 × 3 = 12 | Anti-slip flooring installed (R11 rating minimum). Cable management system (overhead reels or floor channels). Spill containment trays under all batteries. Immediate clean-up protocol for water/electrolyte spills. Adequate lighting (minimum 300 lux per HSE guidance). Designated walkways marked. Housekeeping inspections weekly. Footwear with slip-resistant soles (SRA rating) mandatory. Warning signage for wet floor conditions. | 2 × 2 = 4 |
Verify the battery charging area ventilation system is operational (check indicator light/alarm). Confirm emergency eyewash station is functional. Don all mandatory PPE (goggles, gloves, apron, safety footwear). Position the MHE in the designated charging bay and apply parking brake. Isolate the MHE by removing the key and applying a personal LOTO device. Inspect battery and charging equipment for visible damage (cracks, leaks, damaged cables). Check portable hydrogen detector is calibrated and functional. Ensure Class D fire extinguisher is accessible within 5 metres.
Ensure charger is switched OFF before making connections. Open battery compartment and inspect terminals for corrosion or damage. Remove any terminal covers. Connect charger leads to battery terminals: RED to POSITIVE (+) first, then BLACK to NEGATIVE (-). Ensure connections are tight and secure to prevent arcing. Verify correct charger settings for battery type and voltage (consult battery label and charger manual). Check that automatic shut-off function is enabled. Ensure charging cables are routed safely without creating trip hazards.
Switch on the battery charger and verify charging has commenced (check indicator lights/display). Record start time, battery identification number, and initial voltage reading in the battery maintenance log. Ensure battery compartment lid is open or vented to allow hydrogen gas to disperse. Position hydrogen detector within 30cm of battery top and verify LEL reading is below 10% (should read 0% initially). Place 'CHARGING IN PROGRESS - DO NOT DISCONNECT' warning sign on MHE. Maintain minimum 2-metre exclusion zone for ignition sources. Do not leave charging area until satisfied all safety measures are in place.
Once charger indicates completion (automatic shut-off or green indicator), switch OFF charger at mains. Allow battery to cool for minimum 30 minutes before topping-up - battery temperature should be below 45°C (verify with infrared thermometer if available). During cooling period, maintain ventilation and keep area clear. Record completion time and final voltage reading in maintenance log. Ensure hydrogen levels have returned to zero on detector. Do not proceed to topping-up if battery is still warm to touch or gassing is observed.
Confirm PPE is still correctly fitted (especially goggles and gloves). Remove cell caps carefully - loosen slowly to release any residual pressure. Inspect electrolyte level in each cell - should be 5-10mm above the plates. Using the battery watering gun or topping-up system, add distilled water ONLY to cells below the correct level. Fill to the indicator mark or 5mm above plates - do NOT overfill. Check specific gravity with hydrometer if required by maintenance schedule (should read 1.265-1.285 for fully charged battery). Replace all cell caps securely. Wipe down battery top with damp cloth to remove any spillage. Dispose of contaminated materials in designated waste container.
Ensure charger is switched OFF. Disconnect charging leads in reverse order: BLACK (negative) first, then RED (positive). Replace terminal covers. Close and secure battery compartment. Remove LOTO device and 'Charging in Progress' signage. Complete battery maintenance log with all required information (date, time, operator signature, any observations). Inspect MHE for readiness (tyre condition, hydraulics, lights, horn). Remove and properly store all PPE. Return MHE key to designated location or hand over to next operator with verbal confirmation that charging is complete. Clean and return all tools and equipment to storage.
EMERGENCY PROCEDURES: In the event of hydrogen gas alarm activation, evacuate the area immediately, activate the emergency stop on charging equipment if safe to do so, and call emergency services (999). Do not re-enter until atmosphere is confirmed safe by Fire Service or competent gas tester. For acid spillage, contain with spill kit absorbent materials, neutralise with sodium bicarbonate, and dispose as hazardous waste per site procedures. For electrical fire, use Class D dry powder extinguisher only - never use water. Isolate power at mains if safe to do so. FIRST AID: Acid contact with skin - remove contaminated clothing, irrigate affected area with copious running water for minimum 15 minutes, seek immediate medical attention. Acid in eyes - irrigate immediately at eyewash station for minimum 15 minutes while holding eyelids open, seek emergency medical treatment (potential sight-threatening injury). Inhalation of acid mist/hydrogen - move casualty to fresh air, keep warm and at rest, seek medical attention if symptoms persist. Electrical shock - do NOT touch casualty if still in contact with electricity, isolate power source, call 999, commence CPR if trained and casualty is not breathing. All incidents must be reported to supervisor immediately and recorded in accident book per RIDDOR requirements. Emergency contact numbers must be displayed at charging station.
Under DSEAR 2002 Regulation 6, employers must ensure adequate ventilation to prevent accumulation of hydrogen gas to explosive concentrations (LEL is 4% v/v). HSG136 and HSG176 recommend minimum 5 air changes per hour for battery charging areas, with mechanical ventilation interlocked to charging equipment. Adequacy is verified through: (1) DSEAR risk assessment by competent person identifying Zone 2 classification, (2) ventilation system design calculations by qualified engineer, (3) routine testing of airflow rates (annually minimum), (4) use of calibrated hydrogen detectors set to alarm at 10% LEL (0.4% v/v), and (5) visible/audible indicators confirming ventilation operation. The charging area should be designated with appropriate ATEX signage, and charging must not proceed if ventilation fails. Document all verification activities in your DSEAR maintenance log.
Under PUWER 1998 Regulation 6, battery charging equipment must be inspected at intervals determined by risk assessment, but HSE guidance recommends: (1) Daily user checks (visual inspection for damage, correct operation), (2) Formal inspections every 6 months by competent person, (3) PAT testing at intervals per IET Code of Practice (typically 6-12 months for industrial equipment), and (4) Thorough examination of lifting equipment (battery handling) annually per LOLER 1998. A 'competent person' under PUWER must have sufficient training, experience, and knowledge - for electrical equipment this typically means City & Guilds 2377 PAT Testing qualification or equivalent, plus understanding of battery charging hazards. All inspections must be documented with defects rectified before continued use. Equipment found defective must be taken out of service, tagged, and isolated until repaired by qualified technician.
Under COSHH 2002 Regulation 6, a suitable and sufficient risk assessment must be completed before work with sulphuric acid electrolyte commences. The assessment must: (1) identify hazards (corrosive, respiratory irritant - H314, H335), (2) determine exposure routes (skin contact, eye splash, inhalation of mist), (3) evaluate existing controls and their adequacy, (4) establish hierarchy of controls (elimination, substitution, engineering controls, PPE), and (5) identify emergency procedures. The assessment must be reviewed annually or when significant changes occur. Health surveillance (Regulation 11) is required if: (a) exposure may cause identifiable disease/health effect, (b) valid surveillance techniques exist, and (c) likelihood of disease occurring under working conditions. For routine battery topping-up with adequate controls, health surveillance is typically not required, but must be considered if employees report symptoms (skin sensitisation, respiratory issues) or exposure incidents occur. Maintain exposure records and provide COSHH training to all operatives with refresher every 12 months. Ensure SDS is available and emergency eyewash facilities are provided within 10 metres per BS EN 15154.
Competent Person & Operative Declaration: By signing below, the Site Supervisor confirms this assessment has been adapted and verified for actual site conditions, and operatives confirm they have attended the pre-start Toolbox Talk for Traction Battery Charging & Distilled Water Topping-Up Procedure and will follow the safe system of work.
| Operative / Supervisor Name | Trade / Role & CSCS No. | Signature | Date & Time |
|---|---|---|---|
| 1. (Site Supervisor): | |||
| 2. | |||
| 3. | |||
| 4. | |||
| 5. | |||
| 6. |