This Standard Operating Procedure (SOP) provides comprehensive guidance for the safe offloading, connection, and transfer of chemicals from 1000-litre Intermediate Bulk Containers (IBCs) using bunded transfer pump systems. The procedure ensures compliance with the Control of Substances Hazardous to Health Regulations 2002 (COSHH), ADR Carriage of Dangerous Goods regulations, and Environmental Protection Act 1990. It addresses chemical exposure hazards, manual handling risks, environmental spillage prevention, and equipment integrity verification. All personnel must be trained in chemical handling, emergency response procedures, and the use of bunded containment systems. This SOP applies to all chemical offloading operations involving IBCs and requires strict adherence to permit-to-work systems where applicable.
| Identified Hazard & Harm | Initial Risk (L×S) | Mandatory Engineering, Isolation & Procedural Controls | Residual Risk |
|---|---|---|---|
| 1. Chemical exposure via skin contact, inhalation, or ingestion during IBC valve opening and pump connection Harm: Chemical burns, respiratory irritation, systemic poisoning, sensitisation, or long-term health effects depending on substance |
4 × 4 = 16 | Mandatory SDS review before operations. Full chemical PPE ensemble (Type 4 coveralls, face shield, chemical gloves per BS EN ISO 374). Work in well-ventilated area or use local exhaust ventilation (LEV). Closed-loop transfer system with sealed connections. Emergency eyewash and safety shower within 10m. Two-person buddy system for hazardous chemicals. Pre-task toolbox talk covering chemical hazards. | 2 × 3 = 6 |
| 2. Environmental spillage and bund overflow due to overfilling, hose failure, or connection leak Harm: Soil/watercourse contamination, regulatory prosecution under EPA 1990, environmental damage, costly remediation |
4 × 3 = 12 | Mandatory use of bunded containment pallet (110% capacity minimum). Visual inspection of all hoses and connections for damage before use. Pressure testing of transfer system before chemical introduction. Overfill protection on receiving vessel with high-level alarm/auto-shutoff. Spill kit (minimum 100L absorbent capacity) positioned within 5m. Drip trays under all connection points. Regular bund integrity inspections documented. Emergency spill response procedure displayed. | 2 × 2 = 4 |
| 3. Manual handling injury during IBC positioning, valve manipulation, or pump installation Harm: Musculoskeletal disorders, back strain, crush injuries, trapped fingers, or acute soft tissue damage |
4 × 3 = 12 | Mechanical handling aids mandatory - use pallet truck or forklift with IBC handling attachment. Never manually lift or tip IBCs. Team lift (minimum 2 persons) for pump equipment >15kg. Ergonomic valve keys and torque-limiting tools to reduce force requirements. Anti-slip flooring in offloading area. Clear access routes maintained. Manual handling training refreshed annually. Pre-operation dynamic risk assessment. | 2 × 2 = 4 |
| 4. Static electricity ignition of flammable vapours during transfer of Class 3 flammable liquids Harm: Fire, explosion, severe burns, facility damage, or fatalities |
3 × 5 = 15 | Bonding and earthing of IBC, pump, and receiving vessel mandatory before operations (resistance <10 ohms verified). Use conductive/antistatic hoses with continuous earthing wire. Intrinsically safe (ATEX-rated) pumps and equipment in Zone 1/2 areas. Eliminate ignition sources - no hot work, mobile phones, or smoking within 10m. Antistatic PPE and footwear (BS EN ISO 20345 S5). Vapour monitoring where required. Permit-to-work for flammable transfers. Inert gas blanketing for highly flammable substances. | 1 × 5 = 5 |
| 5. Equipment failure or pressure surge causing hose whip, connection rupture, or pump seal failure Harm: High-pressure chemical spray causing severe chemical burns, eye damage, or large-scale environmental release |
3 × 4 = 12 | Pre-use inspection regime - hoses checked for abrasion, kinking, age degradation (max 5-year service life). Pressure rating verification - hoses and fittings rated >150% maximum pump pressure. Secure all connections with safety clips/locking mechanisms. Pressure relief valve fitted to pump discharge. Hose restraint systems or whip-checks on high-pressure lines. Pump flow rate controlled to prevent surge. Isolation valves at IBC and receiving vessel for emergency shutdown. Competent person sign-off on equipment integrity. | 1 × 3 = 3 |
Establish exclusion zone with barrier tape (3m radius minimum). Review Safety Data Sheet (SDS) for chemical being transferred - note UN number, GHS hazards, PPE requirements, and emergency measures. Inspect IBC for damage, leaks, and verify UN certification plate is legible and in-date. Check bunded pallet is clean, dry, and structurally sound with no cracks or drain valve open. Inspect transfer pump, hoses, and connections for damage, wear, or contamination. Verify hose age markings (reject if >5 years old). Position spill kit and emergency equipment. Confirm emergency eyewash/shower operational. Complete pre-task checklist and obtain permit-to-work if required.
Don full chemical PPE ensemble in correct sequence: coveralls, safety boots, chemical-resistant gloves (inspect for holes), safety goggles or face shield. Ensure gloves overlap coverall sleeves. Using mechanical handling equipment (pallet truck/forklift), carefully position IBC onto centre of bunded containment pallet. Ensure IBC is stable and level - use wedges if necessary. Verify IBC outlet valve is in closed position and dust cap is secure. Check bund drain valve is closed and sealed. Place drip tray under IBC outlet valve. Ensure adequate working space around IBC for safe access.
For flammable liquids (Class 3): Connect earthing cable from verified earth point to IBC metal frame or conductive band. Verify earth continuity <10 ohms using resistance meter. Connect bonding cable between IBC and pump, and pump to receiving vessel. Remove IBC dust cap slowly to allow pressure equalisation. Install valve adaptor to IBC outlet using appropriate seals (PTFE/Viton) - hand-tighten then use torque wrench to manufacturer specification. Insert pump dip-tube or suction lance through adaptor into IBC ensuring it reaches bottom but does not obstruct flow. Secure pump assembly and connect discharge hose to receiving vessel. Ensure all connections have secondary containment (drip trays) beneath.
With IBC valve still closed, perform pressure test: activate pump briefly to pressurise hose system (if applicable to pump type). Inspect all connections for leaks - look for drips, seepage, or vapour release. Tighten connections if minor seepage detected; replace components if leaks persist. Calculate receiving vessel available capacity and verify it can accommodate full IBC volume (1000L) plus safety margin. Check receiving vessel high-level alarm is functional. Verify receiving vessel is also appropriately bunded. Position observer at receiving vessel to monitor fill level throughout transfer. Establish communication method (radio/visual signals) between IBC operator and receiving vessel observer.
Stand to side of valve (not directly in front) and slowly open IBC outlet valve in quarter-turn increments. Monitor initial flow for leaks or spray. Once flow is stable, open valve fully. Activate transfer pump according to manufacturer instructions (air supply for pneumatic, power for electric). Monitor pump operation - listen for unusual noises indicating cavitation or seal failure. Maintain visual observation of all connection points, bund level, and hose condition throughout transfer. Receiving vessel observer must continuously monitor fill level and be prepared to signal emergency stop. Control transfer rate to prevent splashing or turbulence. Do not leave transfer operation unattended. Record start time and estimated completion time.
When IBC is empty or transfer complete, shut down pump and allow system to depressurise. Close IBC outlet valve fully. For residual chemical in hoses: pump through to receiving vessel or drain into suitable container within bund. Do not disconnect pressurised hoses. Carefully disconnect pump assembly - expect residual drips, ensure drip tray is positioned. Cap IBC outlet immediately with dust cap. Remove earthing/bonding cables in reverse order. Inspect bund for any spillage - absorb with spill kit materials if present. Decontaminate external surfaces of pump and hoses with appropriate cleaning agent per SDS. Store equipment in designated area. Complete transfer documentation including volume transferred, any incidents, and equipment condition. Dispose of contaminated PPE and absorbent materials as hazardous waste per site procedures.
EMERGENCY RESPONSE: In event of major spill: Activate emergency alarm, evacuate non-essential personnel upwind, establish 25m exclusion zone. Contain spill using absorbent booms/pads from spill kit - prevent entry to drains or watercourses. For spills >50L or environmental release, notify Environment Agency Incident Hotline (0800 807060) immediately. Implement site emergency spill plan. For fire involving flammable chemicals: Evacuate area, call 999, use appropriate extinguisher only if safe (foam/CO2 for Class 3 flammables - never water). For pump/hose failure with chemical release: Execute emergency shutdown - close IBC valve, stop pump, isolate power/air supply. FIRST AID: Skin contact - remove contaminated clothing, irrigate affected area with copious water for minimum 15 minutes, seek medical attention. Eye contact - irrigate with eyewash or clean water for minimum 15 minutes holding eyelids open, seek immediate medical attention. Inhalation - move casualty to fresh air, keep warm and at rest, seek medical attention if symptoms persist. Ingestion - do NOT induce vomiting, rinse mouth with water, seek immediate medical attention. Always provide SDS to medical personnel. For serious injuries or unconsciousness, call 999 immediately and commence first aid/CPR as trained.
Under COSHH Regulation 6, employers must conduct a suitable and sufficient risk assessment before commencing any work involving hazardous substances, including IBC chemical transfers. The assessment must identify hazards, evaluate risks, and determine adequate control measures including PPE, engineering controls, and safe systems of work. COSHH Regulation 12 requires health surveillance for certain substances (e.g., respiratory sensitisers, carcinogens). Risk assessments must be reviewed regularly - at minimum annually, but also whenever there is significant change (new chemical, different equipment, incident occurrence, or change in legislation). The assessment must be documented, and all operatives must be trained on the findings and control measures. Regulation 8 requires control measures to be properly maintained and examined/tested at suitable intervals (e.g., LEV systems tested every 14 months). Failure to comply can result in enforcement action including Improvement/Prohibition Notices or prosecution.
Chemical compatibility verification is critical and must be completed before any transfer operation. Step 1: Consult the Safety Data Sheet (SDS) Section 10 (Stability and Reactivity) and Section 7 (Handling and Storage) for material compatibility guidance. Step 2: Cross-reference the chemical against manufacturer compatibility charts for IBC material (typically HDPE, but verify), pump wetted parts (seals, diaphragms, O-rings - commonly Viton, PTFE, EPDM), and hose material (nitrile, EPDM, PTFE-lined). Step 3: Check for specific incompatibilities - e.g., strong oxidisers attack many elastomers, aromatic hydrocarbons swell nitrile rubber, concentrated acids require PTFE or Viton. Step 4: Verify temperature compatibility - elevated temperatures accelerate chemical attack. Step 5: When in doubt, conduct a compatibility test or consult chemical/equipment supplier technical support. Never assume compatibility - incompatible materials can degrade rapidly causing seal failure, hose rupture, or IBC structural failure, resulting in major chemical release and potential injury. Document compatibility verification as part of pre-task checks.
For flammable liquids (GHS Category 1-3, UN Class 3), earthing and bonding is mandatory under the Dangerous Substances and Explosive Atmospheres Regulations 2002 (DSEAR) to prevent static electricity accumulation and discharge. Earthing connects equipment to true earth (0V potential) via a verified earth point. Bonding connects all conductive components together to equalise potential and prevent spark discharge between them. Requirements: (1) Connect earthing cable from verified earth point (building earth stake/system) to IBC metal frame or conductive band - verify resistance to earth is <10 ohms using calibrated resistance meter. (2) Bond IBC to pump, and pump to receiving vessel using conductive bonding cables - verify resistance between components <10 ohms. (3) Use conductive/antistatic hoses with continuous earthing wire. (4) Ensure all personnel wear antistatic footwear and work on conductive flooring. (5) Establish earthing/bonding BEFORE opening IBC or introducing chemical. (6) Maintain earthing throughout transfer - do not disconnect until operation complete and system purged. (7) Use ATEX-rated equipment in classified hazardous areas. Verification: Use calibrated earth bond tester before each operation - document readings. Never rely on visual inspection alone. Static discharge can occur at <1000V but is invisible - proper earthing/bonding is the only reliable control.
Competent Person & Operative Declaration: By signing below, the Site Supervisor confirms this assessment has been adapted and verified for actual site conditions, and operatives confirm they have attended the pre-start Toolbox Talk for 1000L IBC Chemical Offloading & Bunded Transfer Pump Connection and will follow the safe system of work.
| Operative / Supervisor Name | Trade / Role & CSCS No. | Signature | Date & Time |
|---|---|---|---|
| 1. (Site Supervisor): | |||
| 2. | |||
| 3. | |||
| 4. | |||
| 5. | |||
| 6. |