SafeSequence › UK Safety Template Library › Packaging & End-of-Line › High-Speed Case Erector Hot-Melt Adhesive Reservoir Refill & Nozzle Unblocking
Verified UK SOP Standard • Packaging & End-of-Line

High-Speed Case Erector Hot-Melt Adhesive Reservoir Refill & Nozzle Unblocking (SOP Template & 5x5 Risk Assessment)

This Standard Operating Procedure (SOP) provides comprehensive safety controls for refilling hot-melt adhesive reservoirs and unblocking nozzles on high-speed case erector machinery in packaging and end-of-line operations. The procedure addresses critical thermal hazards (molten adhesive at 160-180°C), mechanical entrapment risks, and chemical exposure in accordance with the Provision and Use of Work Equipment Regulations 1998 (PUWER), specifically Regulations 11 (dangerous parts) and 12 (protection against specified hazards including extreme temperatures). All tasks require mandatory Lock-Out Tag-Out (LOTO) isolation procedures, permit-to-work authorisation, and use of BS EN 407 certified thermal protective equipment. This SOP is designed for trained maintenance technicians and packaging operatives who have completed competency assessments in hot-melt adhesive system maintenance and PUWER compliance. The document incorporates 5x5 risk matrix assessments demonstrating risk reduction from high initial scores to tolerable residual levels through engineering controls, administrative procedures, and appropriate PPE selection.

Statutory FrameworkPUWER 1998 (Reg 11 & Reg 12 Thermal Hazards), LOTO Isolation Standard, BS EN 407 Thermal PPE
ClassificationHot-melt adhesives typically contain ethylene-vinyl acetate (EVA) copolymers, hydrocarbon resins, and tackifiers. GHS Classification: Not classified as hazardous under CLP Regulation (EC) 1272/2008 in solid form at ambient temperature. However, when heated above 160°C, thermal decomposition may produce irritant vapours. H-Statements (when heated): H319 (Causes serious eye irritation), H335 (May cause respiratory irritation). P-Statements: P261 (Avoid breathing fume/vapour), P280 (Wear protective gloves/eye protection), P305+P351+P338 (IF IN EYES: Rinse cautiously with water for several minutes), P403+P233 (Store in well-ventilated place, keep container tightly closed). UN Number: Not classified for transport in solid form. Flash Point: >200°C (closed cup). Ensure Safety Data Sheet (SDS) for specific adhesive product is available at workstation and reviewed prior to task commencement. Molten adhesive contact causes severe thermal burns requiring immediate first aid intervention.
Required Plant / KitLOTO isolation kit (padlocks, tags, lockout hasps) compliant with company isolation standard • Hot-melt adhesive pellets or blocks (manufacturer-approved grade for case erector system) • Brass or bronze nozzle cleaning rods (non-sparking, heat-resistant to 250°C) • Infrared non-contact thermometer (measuring range 0-250°C, ±2°C accuracy) • Insulated stainless steel funnel with extended spout for adhesive reservoir filling
Review Cycle12 Months / Post-Incident
Instant AI Customization or Free Blank Word (.doc) Download

Need this SOP customized with your Company Name, Site Postcode & Nearest A&E Hospital?

Dictate your site specifics on your phone in 45 seconds to auto-compile a signed PDF—or download our free blank Word (.doc) shell below.

Auto-Fill via Voice / CLP (45s)

2. 5×5 Hazard Risk Assessment Matrix (HASAWA 1974 / MHSWR 1999)

Identified Hazard & HarmInitial Risk (L×S)Mandatory Engineering, Isolation & Procedural ControlsResidual Risk
1. Severe thermal burns from molten hot-melt adhesive contact (160-180°C)
Harm: Full-thickness burns requiring hospital treatment, permanent scarring, potential for shock if large body surface area affected
4 × 5 = 20LOTO isolation of adhesive pump and heater circuits verified with infrared thermometer (<50°C before intervention). BS EN 407 Level 3 thermal gloves mandatory. Full-face shield prevents facial burns. Insulated funnel eliminates hand proximity to reservoir opening. Nozzle unblocking only when system depressurised and cooled. Emergency eyewash/drench shower within 10m.2 × 4 = 8
2. Mechanical entrapment in case erector forming heads or conveyor systems
Harm: Crush injuries to hands/fingers, amputation, fractures requiring surgical intervention
3 × 5 = 15PUWER Reg 11 compliance: Multi-point LOTO isolation (electrical, pneumatic, hydraulic) with personal padlock. Zero Mechanical State verification—all moving parts stationary, pneumatic pressure vented, stored energy dissipated. Permit-to-work system with authorised person sign-off. Barricade work zone with 'Maintenance in Progress' signage. Buddy system—second person monitors during task.1 × 5 = 5
3. Inhalation of thermal decomposition fumes from overheated adhesive
Harm: Respiratory irritation, occupational asthma, chemical pneumonitis if prolonged exposure
3 × 3 = 9Local exhaust ventilation (LEV) system operational and tested (minimum 0.5 m/s capture velocity at reservoir opening per COSHH assessment). Temperature interlock prevents adhesive exceeding 185°C. Respiratory protective equipment (FFP3 or half-mask with A2P3 filters) if LEV unavailable. Task duration limited to 15 minutes with 5-minute break in fresh air. Pre-task LEV inspection recorded.2 × 2 = 4
4. Pressurised adhesive ejection during nozzle unblocking causing injection injury
Harm: High-pressure injection of molten adhesive into tissue requiring emergency surgical debridement, potential amputation
3 × 5 = 15System depressurisation mandatory—adhesive pump isolated and pressure relief valve opened. Pressure gauge reading zero before nozzle removal. Nozzle cleaning performed with system cold (<50°C) using brass rods (never steel wire). Full-face shield and thermal gloves prevent contact. Nozzle pointed away from body into containment tray. Emergency protocol for injection injury: immediate A&E referral (do not wait for symptoms).1 × 5 = 5
5. Manual handling of 20kg adhesive blocks causing musculoskeletal injury
Harm: Lower back strain, shoulder injury, herniated disc requiring physiotherapy or surgical intervention
4 × 3 = 12Mechanical lifting aid (hoist or scissor lift table) positioned adjacent to reservoir for blocks >15kg per Manual Handling Operations Regulations 1992. Two-person lift for blocks 15-25kg with coordinated technique. Adhesive storage at waist height (750-1050mm) eliminates floor-level lifting. Pre-task dynamic risk assessment identifies lifting hazards. Operatives trained in kinetic lifting techniques with annual refresher.2 × 2 = 4

3. Step-by-Step Safe Sequence of Operations & Hold-Points

1

Implement LOTO isolation and verify Zero Energy State

Preparation & Isolation

Notify production supervisor and obtain permit-to-work authorisation. Implement multi-point LOTO isolation: (1) Isolate electrical supply at main isolator and apply personal padlock; (2) Close pneumatic supply valve and vent residual pressure via bleed valve; (3) Isolate adhesive pump motor and heater circuits at local isolator. Attach LOTO tags with name, date, and task description. Attempt to restart machine to verify isolation effectiveness (dead test). Use infrared thermometer to confirm adhesive temperature <50°C at reservoir and nozzles. Erect barriers and 'Maintenance in Progress—Do Not Operate' signage around work zone. Document isolation on permit-to-work form.

Critical Hold-Point: CRITICAL HOLD POINT: Do not proceed until adhesive temperature verified <50°C and Zero Mechanical State confirmed. Molten adhesive contact at operating temperature (160-180°C) causes immediate full-thickness burns. Unauthorised re-energisation during maintenance has resulted in fatal entrapment incidents in packaging operations.
2

Inspect adhesive system and verify LEV operation

Pre-Task Inspection

Don all mandatory PPE (thermal gloves, full-face shield, heat-resistant apron, safety footwear). Inspect adhesive reservoir for cracks, corrosion, or adhesive carbonisation indicating overheating. Check reservoir level gauge—refill required when <25% capacity. Verify local exhaust ventilation (LEV) system operational using smoke tube or anemometer (minimum 0.5 m/s capture velocity). Inspect nozzles for visible blockages or adhesive build-up. Check emergency eyewash/drench shower operational (15-minute flow test within 7 days). Review adhesive SDS and confirm correct grade available. Identify nearest first aider and emergency contact numbers.

Critical Hold-Point: STOP: If LEV system inoperative or reservoir shows structural damage, do not proceed. Notify engineering manager and use RPE (FFP3 minimum) if task critical. Damaged reservoirs can fail catastrophically, releasing large volumes of molten adhesive.
3

Refill hot-melt adhesive reservoir using insulated funnel

Adhesive Reservoir Refill

Position insulated stainless steel funnel securely in reservoir fill port (ensure stable—do not hand-hold). Open adhesive block packaging and inspect for contamination or moisture (discard if compromised). Using two-person lift technique or mechanical aid, transfer adhesive blocks into funnel. Break large blocks into smaller pieces if required to fit funnel opening. Fill reservoir to 75-80% capacity (never exceed maximum fill line to allow thermal expansion). Remove funnel and replace reservoir cap, ensuring gasket seated correctly. Wipe any adhesive residue from reservoir exterior using heat-resistant cloth. Dispose of packaging in designated waste container. Record refill quantity and date on reservoir maintenance log.

Critical Hold-Point: WARNING: Overfilling reservoir (>80% capacity) can cause adhesive overflow when heated, creating slip hazards and fire risk if contacting electrical components. Never introduce wet or contaminated adhesive—moisture causes violent steam generation when heated.
4

Remove and clean blocked adhesive nozzles

Nozzle Unblocking

Confirm system depressurised—adhesive pump isolated and pressure gauge reading zero. Open pressure relief valve if fitted. Using thermal gloves, carefully unscrew blocked nozzle assembly (turn anti-clockwise). Place nozzle in metal containment tray positioned on stable surface. Select appropriate diameter brass cleaning rod (never use steel—risk of sparking and nozzle damage). Insert rod gently into nozzle orifice and push blockage through from feed end to discharge end. Rotate rod if resistance encountered. For stubborn blockages, soak nozzle in approved solvent (per manufacturer specification) for 10 minutes, then re-attempt cleaning. Inspect nozzle orifice for damage or wear—replace if diameter enlarged >10% of original specification. Reinstall cleaned nozzle, ensuring thread engagement correct and torque to manufacturer specification (typically 15-20 Nm).

Critical Hold-Point: CRITICAL: Never attempt nozzle removal or cleaning while system pressurised or above 50°C. Pressurised molten adhesive injection into tissue is a surgical emergency requiring immediate hospital treatment. Point nozzle away from body during cleaning—never look directly into orifice.
5

Reinstate adhesive system and perform function test

System Reinstatement

Ensure all tools, cleaning materials, and packaging removed from work area. Verify reservoir cap secured and all nozzles correctly installed. Remove LOTO devices in reverse order of application: (1) Remove personal padlocks and tags; (2) Restore pneumatic supply; (3) Restore electrical supply at main isolator. Set adhesive system temperature controller to operating setpoint (typically 165-175°C per manufacturer specification). Allow 30-45 minute heat-up period—monitor temperature rise using infrared thermometer. Once at temperature, activate adhesive pump and observe nozzle flow pattern—should be consistent, conical spray without drips or deviation. Check for leaks at nozzle connections and reservoir seals. Run case erector through one complete cycle with scrap material to verify adhesive application quality. Record system reinstatement time and function test results on permit-to-work form.

Critical Hold-Point: HOLD POINT: Do not leave heating system unattended during initial heat-up. Temperature controller failure can cause adhesive overheating (>200°C), generating toxic fumes and fire risk. Maintain 1-metre exclusion zone around reservoir during heat-up period.
6

Complete documentation and restore normal operations

Post-Task & Documentation

Remove barriers and 'Maintenance in Progress' signage. Clean work area of any adhesive residue or spills using approved cleaning solvent and absorbent materials. Dispose of contaminated materials in designated hazardous waste container (adhesive waste classified as non-hazardous but requires controlled disposal). Return all tools to designated storage. Complete permit-to-work closure section with task completion time, any issues encountered, and sign-off. Update adhesive system maintenance log with refill quantity, nozzles cleaned/replaced, and next service due date. Notify production supervisor that case erector available for operation. Conduct post-task debrief with team—identify any near-misses or improvement opportunities. File completed permit-to-work in maintenance records (retain for minimum 5 years per PUWER requirements).

Critical Hold-Point: IMPORTANT: Ensure all LOTO devices removed before handover to production—equipment left in isolated state has caused production delays and created hazards when operators attempted unauthorised re-energisation. Verify machine returns to normal operating parameters before leaving area.

Emergency Rescue, First Aid & Spill Protocol

MOLTEN ADHESIVE BURNS: Do NOT attempt to remove solidified adhesive from skin—this will worsen tissue damage. Immediately cool affected area with lukewarm running water (15-20°C) for minimum 20 minutes. Do not use ice or very cold water (causes vasoconstriction reducing heat dissipation). Cover burn with sterile non-adherent dressing. Administer oxygen if available and treat for shock. Evacuate to A&E immediately—all molten adhesive burns require hospital assessment regardless of apparent severity. For eye contact: Irrigate with eyewash for minimum 15 minutes, holding eyelids open. Do not allow casualty to rub eyes. Immediate ophthalmology referral required. INJECTION INJURY: If molten adhesive injected under skin (high-pressure incident), do NOT wait for symptoms to develop. This is a surgical emergency requiring immediate debridement within 6 hours to prevent tissue necrosis and potential amputation. Apply cold compress, elevate affected limb, and evacuate to A&E immediately with SDS. Inform medical staff this is a high-pressure injection injury requiring specialist hand surgery consultation. INHALATION OF FUMES: Remove casualty to fresh air immediately. Loosen tight clothing. If breathing difficult, administer oxygen and place in recovery position. Monitor for delayed pulmonary oedema (can develop 24-48 hours post-exposure). Seek medical attention if symptoms persist beyond 30 minutes or if exposure was prolonged (>15 minutes). FIRE: Hot-melt adhesive is combustible above 200°C. Use CO2 or dry powder extinguisher (never water—causes violent spattering). Evacuate area and call emergency services if fire cannot be controlled immediately. All incidents must be reported via company RIDDOR procedures and investigated by competent H&S personnel within 24 hours.

4. UK HSE Compliance FAQs: High-Speed Case Erector Hot-Melt Adhesive Reservoir Refill & Nozzle Unblocking

What is the legal basis under PUWER 1998 for requiring LOTO isolation during hot-melt adhesive system maintenance, and how does this differ from simply switching off the machine?

PUWER 1998 Regulation 19 requires that work equipment is shut down and isolated from all sources of energy before maintenance work begins, with isolation measures remaining effective throughout the work period. Regulation 11 (dangerous parts of machinery) and Regulation 12 (protection against specific hazards including extreme temperatures) impose absolute duties to prevent access to dangerous parts and protect against thermal hazards. Simply switching off the machine does not achieve a Zero Energy State—residual thermal energy in the adhesive reservoir (which can remain above 100°C for 2+ hours), stored pneumatic pressure, and potential for unauthorised re-energisation create foreseeable risks. LOTO isolation with personal padlocks provides physical prevention of re-energisation (not just procedural control), ensuring the 'hierarchy of control' principle is applied with engineering controls taking precedence over administrative measures. The HSE's guidance INDG229 'Working on Electrical Equipment' and sector-specific ACOPs emphasise that isolation must be secured by the person at risk, not delegated to supervisors or operators. Failure to implement effective isolation has been a causal factor in multiple fatalities prosecuted under PUWER, with courts consistently ruling that 'switching off' does not constitute adequate isolation where foreseeable re-energisation or stored energy presents risk of serious injury.

Why must nozzle unblocking be performed only when the adhesive system is below 50°C, and what is the specific injury mechanism that makes pressurised hot-melt injection injuries so severe?

Hot-melt adhesive systems operate at 160-180°C under pressures of 5-15 bar (75-220 psi) to maintain flow characteristics and atomisation at the nozzle. Attempting to remove or clean nozzles while pressurised creates risk of high-pressure injection injury—a surgical emergency where molten adhesive is forced under the skin into subcutaneous tissue, tendons, or bone. The injury mechanism is threefold: (1) Mechanical trauma from high-velocity penetration creating deep tissue tracks; (2) Thermal burns from 160°C+ material in contact with internal tissues causing immediate necrosis; (3) Chemical inflammation as adhesive components trigger foreign body reaction and compartment syndrome. The adhesive solidifies within seconds, encapsulating tissue and preventing blood flow, leading to rapid necrosis extending far beyond the entry wound. Medical literature documents that delayed treatment (>6 hours) results in amputation rates exceeding 50% for finger injuries. The <50°C threshold ensures: (a) adhesive is solid, eliminating injection risk; (b) thermal burn severity reduced from full-thickness to superficial if contact occurs; (c) system depressurisation is effective (pressure cannot build in solid-phase adhesive). This temperature limit is based on HSE research into thermal hazards (Research Report RR782) and aligns with PUWER Regulation 12's requirement to protect against extreme temperatures through engineering controls rather than relying on PPE alone.

How should a dynamic risk assessment be conducted if the local exhaust ventilation (LEV) system fails during a critical adhesive refill operation, and what are the legal implications under COSHH regulations?

Under the Control of Substances Hazardous to Health Regulations 2002 (COSHH), Regulation 7 requires that exposure to hazardous substances (thermal decomposition products from hot-melt adhesives including aldehydes and volatile organic compounds) be prevented or adequately controlled, with LEV being the preferred engineering control per the hierarchy of control. If LEV fails during operations, a dynamic risk assessment must immediately evaluate: (1) Can the task be safely postponed until LEV is repaired? (2) What is the criticality/business impact of delay? (3) Can exposure be eliminated through alternative methods (e.g., cold nozzle cleaning, using pre-packaged adhesive cartridges)? (4) If task must proceed, what additional controls reduce risk to tolerable levels? The legal position is clear: COSHH Regulation 9 requires that control measures (including LEV) are maintained in efficient working order through thorough examination and testing at suitable intervals (minimum annually for LEV per COSHH ACOP). Operating without functional LEV breaches this duty unless the risk assessment demonstrates that alternative controls (e.g., RPE with assigned protection factor ≥20, reduced task duration, enhanced natural ventilation, continuous air monitoring) achieve equivalent protection. The dynamic risk assessment must be documented, authorised by a competent person (CMIOSH or equivalent), and communicated to all affected workers. Workers have the right under Section 44 Employment Rights Act 1996 to refuse work in circumstances of serious and imminent danger—LEV failure during hot-work with chemical fume generation may constitute such circumstances. Prosecution under COSHH for inadequate exposure control has resulted in fines exceeding £500,000 where LEV deficiencies contributed to occupational disease, emphasising that business continuity cannot override legal duties to control exposure.

5. Operative Toolbox Talk & Competent Person Sign-Off Register

Competent Person & Operative Declaration: By signing below, the Site Supervisor confirms this assessment has been adapted and verified for actual site conditions, and operatives confirm they have attended the pre-start Toolbox Talk for High-Speed Case Erector Hot-Melt Adhesive Reservoir Refill & Nozzle Unblocking and will follow the safe system of work.

Operative / Supervisor Name Trade / Role & CSCS No. Signature Date & Time
1. (Site Supervisor):     
2.     
3.     
4.     
5.     
6.     

Related UK Safety Templates & Risk Assessments